Research

Paper · MERC

Effect of hydraulic retention time and substrate availability in denitrifying bioelectrochemical systems

01

Summary

What the paper reports, in its own words.

AI Enhanced· 82%

Abstract

This paper evaluates the influence of HRT and nitrate content on denitrifying BES.

AI summary

82% confidence

This study demonstrates that decreasing hydraulic retention time (HRT) in a tubular denitrifying bioelectrochemical system dramatically increases nitrate removal rates from 85 g N mNCC⁻³ d⁻¹ at 9.6 h to 849 g N mNCC⁻³ d⁻¹ at 0.46 h, with no nitrite accumulation. The cathode was poised at −0.320 V vs. Ag/AgCl. Critically, the improvement is driven by hydrodynamics and water flux rather than substrate availability alone, and N₂O emissions remain problematic (33–90% of removed NO₃⁻), suggesting the need for design modifications to suppress N₂O production.

Key insights

  • Trade-off Nitrate removal rate increased 10-fold (85 to 849 g N mNCC⁻³ d⁻¹) by decreasing HRT from 9.6 to 0.46 h, but removal efficiency dropped from 100% to 50%, revealing a trade-off between throughput and conversion.

    So what. Operators must choose between high removal rates (low HRT, cascaded reactors) or high conversion (high HRT, single reactor); series operation is recommended to achieve both.

  • Threshold At low HRTs (1.2–1.6 h), nitrate removal rate plateaued at 730–840 g N mNCC⁻³ d⁻¹ above 43.9 mg N L⁻¹ influent NO₃⁻, but at high HRT (3.4 h), activity sharply declined above 40.6 mg N L⁻¹, indicating substrate inhibition at longer residence times.

    So what. Do not operate denitrifying BES at high HRTs with high influent nitrate; low HRT operation is more robust to substrate concentration variation.

  • Mechanism System response to HRT change occurred in <0.25 days despite autotrophic biomass (slow growth ~1 d⁻¹), indicating activity modulation rather than growth, and hydrodynamics—not nitrate availability—is the dominant performance driver.

    So what. Optimize reactor hydrodynamics and flow distribution rather than relying on substrate concentration to improve denitrification rates.

  • Performance N₂O removal rate increased from 39–109 g N mNCC⁻³ d⁻¹ at high HRT to 436–466 g N mNCC⁻³ d⁻¹ at low HRT, but N₂O emissions (as % of removed NO₃⁻) remained high (33–90%), indicating incomplete reduction to N₂.

    So what. Low HRT improves N₂O consumption kinetics but does not eliminate N₂O slip; alternative cathode designs or potentials may be needed to suppress N₂O formation.

  • Trade-off Coulombic efficiency ranged 53–127% across HRTs, with >100% at low HRT indicating excess current supply relative to observed denitrification, suggesting heterotrophic activity or measurement uncertainty at high HRTs.

    So what. At low HRTs, current supply exceeds denitrification demand; consider current control or potential adjustment to improve energy efficiency.

Opportunity areas6

Specific gaps in this paper, with an experiment that would close each.

  • High N₂O formation and reduction mechanism under varying cathode potentials (−0.320 V was fixed); test range −0.1 to −0.5 V vs. Ag/AgCl to identify potential window minimizing N₂O slip.

    N₂O emissions remain 33–90% of removed NO₃⁻ across all HRTs; authors note this is higher than prior work but do not systematically vary potential to suppress N₂O formation.

    Try. Potentiostatic sweep at fixed HRT (0.46 h) from −0.1 to −0.5 V vs. Ag/AgCl; measure NO₃⁻, NO₂⁻, N₂O, and current density.

  • High Effect of internal recirculation or improved hydrodynamics on N₂O reduction; authors hypothesize lack of recirculation drives high N₂O emissions but do not test it.

    Authors state: 'The difference in N₂O emissions could be explained through the different reactor design used' (lack of internal recirculation); no experimental validation provided.

    Try. Retrofit tubular reactor with internal recirculation loop; compare N₂O emissions and removal rates at same HRT (0.46 h) and potential (−0.320 V).

  • Medium Influent NO₃⁻ concentration range above 112 mg N L⁻¹ to determine if inhibition at high HRT (3.4 h) continues or reverses; maximum tested was 112 mg N L⁻¹.

    At HRT 3.4 h, activity declined sharply above 40.6 mg N L⁻¹ (Fig. 5); mechanism unclear (FNA ruled out, no nitrite accumulation); testing higher concentrations may reveal saturation or true inhibition.

    Try. HRT 3.4 h, influent NO₃⁻ 112–200 mg N L⁻¹; measure NO₃⁻ removal rate, NO₂⁻, and pH to assess FNA formation.

  • Medium Microbial community composition and gene expression (nir, nor, nos genes) across HRT range to link hydrodynamic changes to N₂O reduction enzyme activity.

    Authors conclude hydrodynamics dominate performance but do not characterize the microbial response; fast response (<0.25 d) suggests activity modulation, but mechanism is unexplored.

    Try. 16S rRNA and metatranscriptomics at HRT 10.89, 1.2, and 0.46 h; correlate denitrification gene expression with N₂O removal rate.

  • Medium Series operation of compact reactors (as recommended for scaling) not experimentally tested; only single-reactor performance evaluated.

    Authors state: 'an appropriate approximation of scaling-up denitrifying BES would be the implementation of compact reactors connected in series' but provide no data on series performance, inter-reactor NO₃⁻/NO₂⁻ dynamics, or overall conversion.

    Try. Two or three tubular reactors in series at HRT 0.46 h per reactor; measure NO₃⁻, NO₂⁻, N₂O at each outlet; compare overall conversion and N₂O emissions to single reactor.

  • Medium Dissolved oxygen and pH in cathode compartment not monitored; only bulk effluent pH and conductivity reported; local conditions may drive N₂O formation.

    Denitrification intermediates (NO₂⁻, N₂O) are sensitive to local pH and DO; no data on cathode microenvironment; could explain high N₂O emissions.

    Try. Insert pH and DO microsensors in cathode at different radial/axial positions during HRT 0.46 h operation; correlate local conditions with N₂O production.

Generated by MESSAI extraction pipeline · review against source PDF

02

Extracted values

Every value pulled from the paper, with its source, so each number can be checked against the text.

n = 115 extracted values

Select a citation to see the quote, page and confidence behind a value.

15 of 115 extracted rows modelable

  • 7 not canonicalised (no canonical slug)
  • 87 no SI value
  • 4 outside physical bounds
  • 2 not marked applicable to modeling
ParameterValueUnitConfidenceSourceNotesModelable
Current Density (Basis Unresolved)×2372A mNCC⁻³95%
extracted
"In replicate 1, the nitrate consumption rate and current demand increased from 8…" · T=22°C, substrate=nitrate, steady_stateExcluded: no SI value
Nitrate Consumption Rate×285g N mNCC⁻³ d⁻¹95%
extracted
"Eight days later, the denitrifying BES reached stable behavior with a current de…" · T=22°C, substrate=nitrate, steady_stateExcluded: no SI value
Nitrate Consumption Rate×2421g N mNCC⁻³ d⁻¹95%
extracted
"Finally, it increased again to 421 ± 45 g N mNCC−3 d−1 at the maximum nitrate in…" · T=22°C, substrate=nitrate, steady_stateExcluded: no SI value
Nitrate Consumption Rate×2177g N mNCC⁻³ d⁻¹95%
extracted
"On the contrary, at the highest HRT (3.4 h), the nitrate removal trend was diffe…" · T=22°C, substrate=nitrate, steady_stateExcluded: no SI value
Nitrate Consumption Rate×2587g N mNCC⁻³ d⁻¹95%
extracted
"Table 1 shows HRT 0.75 ± 0.01 h with NO3− consumption rate 587 ± 25 g N-NO3− mNC…" · T=22°C, substrate=nitrate, steady_stateExcluded: no SI value
Nitrate Consumption Rate×246%95%
extracted
"In replicate 2, the N2O emission was 46% of the nitrate removed at 10.89 h. It i…" · T=22°C, substrate=nitrate, steady_stateExcluded: no SI value
Energy Consumption×20.0148kW h g N-NO₃⁻ removed95%
extracted
"In replicate 1, at the highest performance (HRT of 0.60 h and rNO3− of 700 ± 7 g…" · T=22°C, substrate=nitrate, steady_stateExcluded: no SI value
Energy Consumption×20.0089kW h g N-NO₃⁻ removed95%
extracted
"Meanwhile in replicate 2, which presented a more stable CE trend, an energy cons…" · T=22°C, substrate=nitrate, steady_stateExcluded: no SI value
Nitrate Consumption Rate×2152g N mNCC⁻³ d⁻¹95%
extracted
"At this HRT, replicate 1 presented an increase of the rNO3− from 152 ± 25 g N mN…" · T=22°C, substrate=nitrate, steady_stateExcluded: no SI value
Nitrate Consumption Rate×2144g N mNCC⁻³ d⁻¹95%
extracted
"Table 1 shows HRT 4.93 ± 0.06 h with NO3− consumption rate 144 ± 3 g N-NO3− mNCC…" · T=22°C, substrate=nitrate, steady_stateExcluded: no SI value
Nitrate Consumption Rate×2700g N mNCC⁻³ d⁻¹95%
extracted
"In replicate 1, the nitrate consumption rate and current demand increased from 8…" · T=22°C, substrate=nitrate, steady_stateExcluded: no SI value
Electrolyte Conductivity4.1mS cm⁻¹95%
extracted
"The conductivity of the medium was adjusted to 4.1 mS cm−1 by controlling the Na…" · T=22°CModelable
Nitrate Consumption Rate×2119g N mNCC⁻³ d⁻¹95%
extracted
"Table 1 shows HRT 5.37 ± 0.15 h with NO3− consumption rate 119 ± 13 g N-NO3− mNC…" · T=22°C, substrate=nitrate, steady_stateExcluded: no SI value
Nitrate Consumption Rate×2466g N mNCC⁻³ d⁻¹95%
extracted
"In replicate 1, the rN2O increased from 109 ± 57 to 466 ± 62 g N mNCC−3 d−1 by l…" · T=22°C, substrate=nitrate, steady_stateExcluded: no SI value
Energy Consumption×20.261kW h mtreated⁻³95%
extracted
"In replicate 1, at the highest performance (HRT of 0.60 h and rNO3− of 700 ± 7 g…" · T=22°C, substrate=nitrate, steady_stateExcluded: no SI value
Chamber Volume×20.24L95%
extracted
"The resulting net cathode volume (net cathode compartment volume – NCC) was 0.24…" · condition_hint=Design parameter, tubular reactorModelable
Nitrate Consumption Rate×2389g N mNCC⁻³ d⁻¹95%
extracted
"Table 1 shows HRT 1.49 ± 0.01 h with NO3− consumption rate 389 ± 13 g N-NO3− mNC…" · T=22°C, substrate=nitrate, steady_stateExcluded: no SI value
Nitrate Consumption Rate×233%95%
extracted
"In replicate 1, the emissions of N2O decreased from 77 to 33% by lowering the HR…" · T=22°C, substrate=nitrate, steady_stateExcluded: no SI value
Nitrate Consumption Rate×277%95%
extracted
"In replicate 1, the emissions of N2O decreased from 77 to 33% by lowering the HR…" · T=22°C, substrate=nitrate, steady_stateExcluded: no SI value
Nitrate Consumption Rate×2849g N mNCC⁻³ d⁻¹95%
extracted
"A nitrate consumption rate of up to 849 g N mNCC−3 d−1 was reached without accum…" · T=22°C, substrate=nitrate, steady_stateExcluded: no SI value
Coulombic efficiency×285%95%
extracted
"Meanwhile, in replicate 2, the CE among the different tests ranged from 85 ± 7% …" · T=22°C, substrate=nitrate, steady_stateModelable
Coulombic efficiency×253%95%
extracted
"In replicate 1, the CE increased from 53 ± 5% at HRT 9.6 h to 127 ± 1% at HRT 0.…" · T=22°C, substrate=nitrate, steady_stateModelable
Nitrate Removal Efficiency×2100%95%
extracted
"Eight days later, the denitrifying BES reached stable behavior with a current de…" · T=22°C, substrate=nitrate, steady_stateModelable
Nitrate Consumption Rate×248%95%
extracted
"In replicate 2, the N2O emission was 46% of the nitrate removed at 10.89 h. It i…" · T=22°C, substrate=nitrate, steady_stateExcluded: no SI value
Influent nitrate concentration33mg N-NO₃⁻ L⁻¹95%
extracted
"It contained 0.20 g L−1 NaNO3 (33 mg N-NO3− L−1)" · T=22°C, substrate=nitrateExcluded: not canonicalised (no canonical slug)
Showing 25 of 63

Methodology

What was the system and how was it run

Methodology

Methodology

Two identical tubular denitrifying bioelectrochemical reactors (0.24 L net cathode volume) were operated in continuous-flow mode with the cathode poised at −0.320 V vs. Ag/AgCl. Influent was organic-carbon-free synthetic medium (33–112 mg N-NO₃⁻ L⁻¹) fed to the cathode; HRT was varied from 10.89 to 0.46 h. Nitrate, nitrite, N₂O, current density, and coulombic efficiency were measured daily for 7 days at each HRT. A second set of experiments evaluated nitrate removal at three fixed HRTs (1.2, 1.6, 3.4 h) across a range of influent NO₃⁻ concentrations (6.5–112 mg N L⁻¹).

System configuration

FieldValue
reactor typeBES
chamber config2-chamber

Performance metrics

FieldValue
citation count31

Operating conditions

29 runs extracted
RunT°CpHanpHcatSubstrate[S]mg/LHRThModeR_extΩV_appVInoculum
v2-00511d9a2157e78122——nitrate33—steady_state—-0.32—
v2-12fa081d0447ca0f22——nitrate32.8—steady_state—-0.32—
v2-13e341410fc26a6922——nitrate33—startup—-0.32—
v2-17a25b1961d3886122——nitrate32.7—steady_state—-0.32—
v2-1dea17f2a425b53622——nitrate36—steady_state—-0.32—
v2-2960de64fd0019bf22——nitrate32.5—steady_state—-0.32—
v2-33562ddd0719d3e522——nitrate35.3—steady_state—-0.32—
v2-3633a5fc358e961c22——nitrate113—steady_state—-0.32—
v2-419bfcfa5a45ff9c22———————-0.32—
v2-49b2674a471e993722——nitrate84.7—steady_state—-0.32—
v2-4e68c20c63b8856222——nitrate33———-0.32—
v2-501a16c8b6a8d7eb22——nitrate32.4—steady_state—-0.32—
v2-560b7f907d5dd88a22——nitrate70.5—steady_state—-0.32—
v2-5e77651d4a6b940622——nitrate33.8—steady_state—-0.32—
v2-63cc5e9c3df3b28022——nitrate35.2—steady_state—-0.32—
v2-8770894074cee85c22——nitrate34.2—steady_state—-0.32—
v2-8a29dc47d2a280cd22——nitrate117—steady_state—-0.32—
v2-a791bab92e31adf122—————————
v2-c1664a3f86cd6f7722——nitrate31.3—steady_state—-0.32—
v2-c67c2d5ba834cc1922——nitrate9.7—steady_state—-0.32—
v2-c80c4eb5d67fa8a722——nitrate35.3—startup—-0.32—
v2-d21175b4e4bdb38522——nitrate120.3—steady_state—-0.32—
v2-d3273a71ab7b026222——nitrate43.9—steady_state—-0.32—
v2-d68e14a7af33eb6a22——nitrate30.5—steady_state—-0.32—
v2-d9b8a5204710930c22——nitrate40.6—steady_state—-0.32—
v2-e24c6f3a93080a6d22——nitrate75—steady_state—-0.32—
v2-e87f0aab0256bd1d22——nitrate33.4—steady_state—-0.32—
v2-f0a0b4abfa6356f822——nitrate——steady_state—-0.32—
v2-f586e9af22985397——————————

Pipeline

Raw extractions, artifacts, quality signal

Extraction quality

honesty signal

Calibrate your trust in the extracted content against these signals — they're how the pipeline rated its own output for this paper.

Parameter completeness

13%

Fraction of expected parameters extracted

Data completeness

40%

Overall extraction coverage across fields

AI confidence

82%

Model self-reported confidence

Mean parameter confidence

88%

Average confidence across PaperParameter rows surfaced above

Last extraction:vpipeline-v2FULL_EXTRACTIONcompleted115 parameters surfaced

review against source PDF before citing · scores 0–1

03

Chart explorer

Move the inputs this paper used and see how the predicted outcome shifts.

04

Explore model

The reactor in 3D, with flow you can switch on and off.

05

AI insights

Contradictions, gaps and opportunities found by comparing this paper with the corpus.

06

Compare similar papers

The nearest papers by system, materials and organisms, with their outcomes side by side.

07

Source PDF

The paper as published.

No 3D model is mapped to this paper yet. The values extracted from it are listed under Extracted values.

MERC
System
85.0percent
Best result · Coulombic efficiency
best of 4
115
Extracted values
2017
Year

Keywords

  • Denitrifying bacteria
  • Nitrate
  • Hydraulic retention time
  • Substrate (aquarium)
  • Denitrification
  • Environmental chemistry

Cite

Narcis Pous, Sebastià Puig, M. Dolors Balaguer et al. (2017). Effect of hydraulic retention time and substrate availability in denitrifying bioelectrochemical systems. Environmental Science: Water Research &amp; Technology. https://doi.org/10.1039/c7ew00145b