Research

Paper · MFC

Shortcut Biological Nitrogen Removal (SBNR) in an MFC Anode Chamber under Microaerobic Conditions: The Effect of C/N Ratio and Kinetic Study

01

Summary

What the paper reports, in its own words.

3D Interactive ModelAI Enhanced· 82%Substrate ·pure compoundPower Generation

Abstract

In this work, the feasibility of the Shortcut Biological Nitrogen Removal (SBNR) in the anodic chamber of a Microbial Fuel Cell (MFC) was investigated. Thirty day experiments were carried out using synthetic wastewaters with a Total Organic Carbon vs. nitrogen ratio (TOC/N) ranging from 0.1 to 1. Ammonium, nitrite, nitrate, pH, and TOC were daily monitored. Results showed that microaerobic conditions in the anodic chamber favored the development of nitritation reaction, due to oxygen transfer from the cathodic chamber through the membrane. Nitritation was found to depend on TOC/N ratio: at TOC/N equal to 0.1 an ammonium removal efficiency of up to 76% was observed. Once the oxygen supply to the cathodic chamber was stopped, denitritation occurred, favored by an increase of the TOC/N ratio: a nitrite removal of 80.3% was achieved at TOC/N equal to 0.75. The presence of nitrogen species strongly affected the potential of the electrochemical system: in the nitritation step, the Open Circuit Voltage (OCV) decreased from 180 mV to 21 mV with the decrease of the TOC/N ratio in the investigated range. Lower OCV values were observed in the denitritation steps since the organic carbon acted as the energy source for the conversion of nitrite to nitrogen gas. A kinetic analysis was also performed. Monod and Blackman models described the ammonium and the organic carbon removal processes well during the nitritation step, respectively, while Blackman-Blackman fitted experimental results of the denitritation step better.

AI summary

82% confidence

This study demonstrates shortcut biological nitrogen removal (SBNR) in an MFC anode chamber by exploiting oxygen diffusion through the cation exchange membrane to enable nitritation (NH₄⁺ → NO₂⁻) under microaerobic conditions, followed by denitritation (NO₂⁻ → N₂) when aeration stops. The process is highly sensitive to TOC/N ratio: nitritation peaks at TOC/N = 0.1 (76% NH₄⁺-N removal), while denitritation optimizes at TOC/N = 0.75 (80.3% NO₂⁻-N removal). OCV drops from 180 mV to 21 mV as TOC/N decreases during nitritation, reflecting the electrochemical cost of nitrogen cycling.

Key insights

  • Threshold Nitritation efficiency increases as TOC/N decreases from 1 to 0.1 (76% removal), because lower organic carbon preserves dissolved oxygen for ammonia oxidation rather than competing heterotrophic oxidation.

    So what. Operate nitritation at TOC/N ≤ 0.1 to maximize ammonia oxidation; higher carbon loads will suppress nitritation and favor heterotrophic respiration instead.

  • Trade-off Denitritation efficiency plateaus above TOC/N = 0.52, with optimal removal at TOC/N = 0.75 (80.3% NO₂⁻-N removal), matching theoretical stoichiometry (0.71) from acetate oxidation and nitrite reduction equations.

    So what. Do not exceed TOC/N = 0.75 in denitritation; excess carbon shifts metabolism toward heterotrophic growth (69.86% TOC removal in D6) rather than nitrite reduction.

  • Mechanism Oxygen diffusion through the cation exchange membrane is essential and controllable: microaerobic conditions (initial DO ~0.4 mg/L in anode) enable nitritation without full aerobic nitrification to NO₃⁻, and stopping cathode aeration switches the anode to anaerobic denitritation.

    So what. Design the cathode aeration schedule as the primary control knob: continuous aeration drives nitritation; cessation enables denitritation. Membrane oxygen permeability is a critical design parameter.

  • Trade-off OCV during nitritation decreases sharply with decreasing TOC/N (180 mV at TOC/N=26 down to 21 mV at TOC/N=0.1), indicating that nitrogen cycling imposes an electrochemical penalty that scales with nitritation intensity.

    So what. Accept that aggressive nitritation (low TOC/N) will suppress electrical output; if power generation is a goal, operate at higher TOC/N and accept lower nitrogen removal, or use a separate nitritation stage.

  • Method Kinetic models differ by process: Monod fits ammonium removal (nitritation), Blackman fits TOC removal (nitritation), and Blackman-Blackman (dual-substrate) fits denitritation, indicating substrate saturation kinetics dominate nitritation while zero-order kinetics emerge at high TOC.

    So what. Use Monod kinetics to predict nitritation startup and rate-limiting substrate (NH₄⁺); use Blackman-Blackman to size denitritation reactors and predict the combined effect of carbon and nitrite availability.

Contradictions1

Tensions the paper itself points to. Each side quotes the passage it comes from.

  • Within the paper Whether oxygen diffusion through the membrane is beneficial or detrimental to the overall process

    One side

    Oxygen diffusion enables nitritation: 'microaerobic conditions in the anodic chamber favored the development of nitritation reaction, due to oxygen transfer from the cathodic chamber through the membrane'

    “microaerobic conditions in the anodic chamber favored the development of nitritation reaction, due to oxygen transfer from the cathodic chamber through the membrane”
    Other side

    Oxygen diffusion reduces electrical efficiency: 'the loss in electrical efficiency can be attributed not only to high internal resistance... but also to the establishment of microaerobic conditions in the anodic chamber that promoted the oxidation of the organic matter'

    “the loss in electrical efficiency can be attributed not only to high internal resistance given by the selected PEM (333 ± 33 Ωload resistance) but also to the establishment of microaerobic conditions in the anodic chamber that promoted the ”

    Authors’ reading. The authors resolve this by noting that oxygen intrusion is necessary for nitritation but comes at the cost of power output; they state 'for the purpose of this work, a further reduction of oxygen concentration in the cell is not desirable, since a little oxygenation is required to favor nitritation', accepting the trade-off as intentional.

Opportunity areas6

Specific gaps in this paper, with an experiment that would close each.

  • High No measurement of dissolved oxygen (DO) in the anode during denitritation phase; only nitritation DO (~0.4 mg/L) is reported. Denitritation requires anaerobic conditions but DO threshold for inhibition is not quantified.

    Section 2.2 states 'Dissolved oxygen in anodic solution was measured using Oximeter Seven GO' but results are only mentioned for nitritation ('initial dissolved oxygen in the anodic chamber was about 0.4 mg/L'). Denitritation DO is not reported, making it unclear whether residual oxygen limits NO₂⁻ reduction or whether the system truly becomes anaerobic.

    Try. Measure anode DO continuously during denitritation (D1–D6 tests) and correlate with NO₂⁻ removal rate; identify the DO threshold below which denitritation rate plateaus or accelerates.

  • High No investigation of N₂O accumulation or emission during denitritation. The paper assumes complete reduction to N₂ but does not measure N₂O or provide a nitrogen balance.

    Equations (3) and (4) show NO₂⁻ → N₂ pathway, but N₂O is a common intermediate in denitrification. The paper does not report N₂O measurements or a full nitrogen balance (inlet N vs. outlet N + N₂ + N₂O). This is critical for environmental compliance and energy recovery.

    Try. Measure N₂O in headspace gas during denitritation using GC-ECD or FTIR; perform nitrogen balance (NO₂⁻-N in vs. NO₂⁻-N out + N₂-N + N₂O-N); vary pH and cathode potential to identify conditions that suppress N₂O.

  • High No systematic variation of cathode potential or anode potential during nitritation and denitritation. OCV is measured but applied potential is not controlled or reported.

    The paper uses open-circuit conditions (no external load) and measures OCV, but does not explore how applied potential (via potentiostat) affects nitritation/denitritation rates or selectivity. Anode potential is known to control nitritation vs. full nitrification in bioelectrochemical systems.

    Try. Operate MFC at fixed anode potentials (e.g., −0.2, 0, +0.2, +0.4 V vs. Ag/AgCl) during nitritation and measure NH₄⁺ removal, NO₂⁻ accumulation, and NO₃⁻ formation; repeat for denitritation with cathode potential control.

  • Medium No exploration of HRT (hydraulic retention time) or batch vs. continuous operation. All tests are 30-day batch experiments; no flow rate, SRT, or continuous-mode data.

    Section 2.1 states 'No addition or recirculation of solution was carried out', meaning all tests are closed-batch systems. For practical wastewater treatment, HRT and continuous operation are essential. The kinetic models (Monod, Blackman) could be used to predict continuous-mode performance but are not validated experimentally.

    Try. Operate the MFC in fed-batch or continuous mode at HRTs of 5, 10, 20 days during nitritation and denitritation; measure steady-state removal rates and compare to batch kinetic predictions.

  • Medium No measurement of cathode potential or cathode-side nitrogen species. The paper focuses entirely on anode chemistry; cathode redox potential and any cathodic nitrogen reduction are not characterized.

    The cation exchange membrane allows ion diffusion; ammonium is stated to not cross ('No ammonium losses through the membrane were observed'), but NO₂⁻ and NO₃⁻ diffusion direction and magnitude are not quantified. Cathode potential is not measured, so the electrochemical driving force for nitrogen species transport is unknown.

    Try. Install reference electrode in cathode chamber; measure anode and cathode potentials simultaneously; perform ion chromatography on cathode effluent to quantify NO₂⁻, NO₃⁻, and NH₄⁺ accumulation; calculate Nernst potential for nitrogen species and compare to measured potentials.

  • Medium No investigation of pH effects on nitritation and denitritation. pH is stated to be 'neutral' but not varied; nitritation and denitritation kinetics are pH-sensitive.

    Section 3.1 states 'In all the tests, a neutral pH condition was always maintained (data not shown)'. Nitritation is known to be inhibited at low pH (H⁺ accumulation from Equation 1), and denitritation is affected by pH-dependent enzyme kinetics. No pH control or variation is reported.

    Try. Operate nitritation tests at pH 6.5, 7.0, 7.5, 8.0 and measure NH₄⁺ removal and NO₂⁻ accumulation; repeat for denitritation; fit pH-dependent kinetic models (e.g., Monod with pH inhibition term).

Generated by MESSAI extraction pipeline · review against source PDF

02

Extracted values

Every value pulled from the paper, with its source, so each number can be checked against the text.

n = 71 extracted values

Select a citation to see the quote, page and confidence behind a value.

31 of 70 extracted rows modelable

  • 38 not canonicalised (no canonical slug)
  • 1 no SI value
ParameterValueUnitConfidenceSourceNotesModelable
Substratewastewater—80%
llm
Electrode Surface Area12.5cm²95%
extracted
"carbon paper electrodes (12.5 cm2; Goodfellow Cambridge Limited, Huntingdon, UK,…" · condition_hint=design parameter, electrode_material=carbon paperModelable
Reactor Volume300mL95%
extracted
"This system was constituted by two 300 mL pyrex glass chambers" · condition_hint=design parameterModelable
External Load2,030Ω95%
extracted
"The electrodes were connected to a resistor (2034 Ω) by means of a titanium wire" · condition_hint=design parameter, external_resistance_ohm=2034Modelable
Total Organic Carbon (TOC) Removal18.6%90%
toc analyzer
"TOC (%) 18.60 in test D1" · pH(an)=7, substrate=acetate, steady_stateModelable
Total Organic Carbon (TOC) Removal18.6%90%
toc analyzer
"TOC (%) 18.55 in test D5" · pH(an)=7, substrate=acetate, steady_stateModelable
Total Organic Carbon (TOC) Removal69.9%90%
toc analyzer
"TOC (%) 69.86 in test D6" · pH(an)=7, substrate=acetate, steady_stateModelable
Total Organic Carbon (TOC) Removal20%90%
toc analyzer
"TOC (%) 20.04 in test D4" · pH(an)=7, substrate=acetate, steady_stateModelable
Total Organic Carbon (TOC) Removal17.9%90%
toc analyzer
"TOC (%) 17.87 in test D3" · pH(an)=7, substrate=acetate, steady_stateModelable
Open Circuit Voltage91mV90%
multimeter against ag/agcl reference electrode
"The maximum OCV values were 196 mV, 165 mV, 91 mV, and 21 mV for N4, N3, N2, and…" · pH(an)=7, substrate=acetate, steady_stateModelable
Ammonium-N Removed76%90%
daily monitoring of ammonium concentration
"at TOC/N equal to 0.1 an ammonium removal efficiency of up to 76% was observed" · pH(an)=7, substrate=acetate, steady_stateModelable
Ammonium-N Removed72%90%
daily monitoring of ammonium concentration
"in tests N1, N2, and N3 ammonium removal of 76%, 72% and 63% was achieved respec…" · pH(an)=7, substrate=acetate, steady_stateModelable
Ammonium-N Removed63%90%
daily monitoring of ammonium concentration
"in tests N1, N2, and N3 ammonium removal of 76%, 72% and 63% was achieved respec…" · pH(an)=7, substrate=acetate, steady_stateModelable
Open Circuit Voltage196mV90%
multimeter against ag/agcl reference electrode
"The maximum OCV values were 196 mV, 165 mV, 91 mV, and 21 mV for N4, N3, N2, and…" · pH(an)=7, substrate=acetate, steady_stateModelable
Total Organic Carbon (TOC) Removal81%90%
toc analyzer
"TOC (%) 81.02 in test N2" · pH(an)=7, substrate=acetate, steady_stateModelable
Open Circuit Voltage21mV90%
multimeter against ag/agcl reference electrode
"the Open Circuit Voltage (OCV) decreased from 180 mV to 21 mV with the decrease …" · pH(an)=7, substrate=acetate, steady_stateModelable
Nitrogen Removal62%90%
ion chromatography
"NO2− (%) 62.00 in test D3" · pH(an)=7, substrate=acetate, steady_stateModelable
Nitrogen Removal40.5%90%
ion chromatography
"NO2− (%) 40.50 in test D2" · pH(an)=7, substrate=acetate, steady_stateModelable
Total Organic Carbon (TOC) Removal20.7%90%
toc analyzer
"TOC (%) 20.70 in test D2" · pH(an)=7, substrate=acetate, steady_stateModelable
Open Circuit Voltage165mV90%
multimeter against ag/agcl reference electrode
"The maximum OCV values were 196 mV, 165 mV, 91 mV, and 21 mV for N4, N3, N2, and…" · pH(an)=7, substrate=acetate, steady_stateModelable
Phosphate Ion Concentration50mM90%
extracted
"synthetic wastewaters were prepared by dissolving sodium acetate as carbon sourc…" · substrate=acetateExcluded: no SI value
Nitrogen Removal79%90%
ion chromatography
"NO2− (%) 79.00 in test D4" · pH(an)=7, substrate=acetate, steady_stateModelable
Total Organic Carbon (TOC) Removal99.4%90%
toc analyzer
"TOC (%) 99.43 in test N4" · pH(an)=7, substrate=acetate, steady_stateModelable
Nitrogen Removal22.4%90%
ion chromatography
"NO2− (%) 22.40 in test D1" · pH(an)=7, substrate=acetate, steady_stateModelable
Nitrogen Removal79.3%90%
ion chromatography
"NO2− (%) 79.30 in test D6" · pH(an)=7, substrate=acetate, steady_stateModelable
Showing 25 of 71

Methodology

What was the system and how was it run

Methodology

Methodology

Batch experiments were conducted in an H-type MFC with two 300 mL chambers separated by a cation exchange membrane (CMI 7000). The anode was inoculated with pre-conditioned microorganisms (AOB for nitritation, denitrifiers for denitritation) and fed with synthetic wastewater containing acetate (TOC source) and either NH₄⁺ or NO₂⁻ (nitrogen source) at TOC/N ratios ranging from 0.1 to 26. The cathode was aerated (nitritation phase) or not aerated (denitritation phase). Daily monitoring included TOC (analyzer), NH₄⁺ (distillation), NO₂⁻ and NO₃⁻ (ion chromatography), pH, and OCV (multimeter with Ag/AgCl reference). Kinetic analysis used Monod, Blackman, and Tessier models fitted to experimental data via Runge-Kutta integration and objective function minimization.

System configuration

FieldValue
reactor typeMFC
chamber config2-chamber

Performance metrics

FieldValue
citation count7

Operational parameters

FieldValue
substrate["wastewater"]

Operating conditions

16 runs extracted
RunT°CpHanpHcatSubstrate[S]mg/LHRThModeR_extΩV_appVInoculum
v2-15b14df8c6cbfd7c—7—acetate540—steady_state2034——
v2-186097f651477bf8—7—acetate120—steady_state2034——
v2-30c4f23419fe1907—7—acetate——startup2034——
v2-39a8b0fa1bc8f7fb—7—acetate——steady_state2034——
v2-6bab446ca5b179e5—7—acetate405—steady_state2034——
v2-855fc201c384ab28—7—acetate280—steady_state2034——
v2-8ba8f0a00bb7034a—7—acetate100—steady_state2034——
v2-a3b411b32577a328—7—acetate2600—steady_state2034——
v2-a951297882e5b494—7—acetate10—steady_state2034——
v2-af10ec9fb29da580—7—acetate35—steady_state2034——
v2-c123eb335f2f0d12—7—acetate60—steady_state2034——
v2-c605c60400575ee2———————2034——
v2-cb8d11102ee52615—7—acetate10—startup2034——
v2-cfd4612f4ab83bef—7—acetate190—steady_state2034——
v2-f2046436d9f74943———acetate——————
v2-f586e9af22985397——————————

Pipeline

Raw extractions, artifacts, quality signal

Extraction quality

honesty signal

Calibrate your trust in the extracted content against these signals — they're how the pipeline rated its own output for this paper.

Parameter completeness

25%

Fraction of expected parameters extracted

Data completeness

50%

Overall extraction coverage across fields

AI confidence

82%

Model self-reported confidence

Mean parameter confidence

85%

Average confidence across PaperParameter rows surfaced above

review against source PDF before citing · scores 0–1

03

Chart explorer

Move the inputs this paper used and see how the predicted outcome shifts.

04

Explore model

The reactor in 3D, with flow you can switch on and off.

05

AI insights

Contradictions, gaps and opportunities found by comparing this paper with the corpus.

06

Compare similar papers

The nearest papers by system, materials and organisms, with their outcomes side by side.

07

Source PDF

The paper as published.

loading 3D model…

Representative model, generic MFC

Representative MFC — matched on the paper’s system type only, not its reactor or geometry.

MFC
System
0.20volts
Best result · Open-circuit voltage
best of 7
71
Extracted values
2018
Year

Keywords

  • Nitrogen
  • Nitrite
  • Ammonium
  • Total organic carbon
  • Anode
  • Carbon fibers

Cite

Irene Bavasso, Daniele Montanaro, Elisabetta Petrucci et al. (2018). Shortcut Biological Nitrogen Removal (SBNR) in an MFC Anode Chamber under Microaerobic Conditions: The Effect of C/N Ratio and Kinetic Study. Sustainability. https://doi.org/10.3390/su10041062

Open in lab for full controls, parameter editing, and template overlays.

Open in lab