Research

Paper · MFC

Denitrification in Microbial Fuel Cells Using Granular Activated Carbon as an Effective Biocathode

01

Summary

What the paper reports, in its own words.

3D Interactive ModelAI Enhanced· 72%Power Generation

Abstract

Nitrate (NO3−-N) and nitrites (NO2−-N) are common pollutants in various water bodies causing serious threats not only to aquatic, but also to animals and human beings. In this study, we developed a strategy for efficiently reducing nitrates in microbial fuel cells (MFCs) powered by a granular activated carbon (GAC)-biocathode. GAC was developed by acclimatizing and enriching denitrifying bacteria under a redox potential (0.3 V) generated from MFCs. Thus, using the formed GAC-biocathode we continued to study their effect on denitrification with different cathode materials and circulation speeds in MFCs. The GAC-biocathode with its excellent capacitive property can actively reduce nitrate for over thirty days irrespective of the cathode material used. The stirring speed of GAC in the cathode showed a steady growth in potential generation from 0.25 V to 0.33 V. A rapid lag phase was observed when a new carbon cathode was used with enriched GAC. While a slow lag phase was seen when a stainless-steel cathode was replaced. These observations showed that effective storage and supply of electrons to the GAC plays a crucial role in the reduction process in MFCs. Electrochemical analysis of the GAC properties studied using electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), and zeta potential showed distinct properties with different abiotic and biocathode conditions. We found that the enrichment of electrotrophic bacteria on GAC facilitates the direct electron transfer in the cathode chamber for reducing NO3−-N in MFCs as observed by scanning electron microscopy.

AI summary

72% confidence

This study demonstrates that granular activated carbon (GAC) enriched with denitrifying bacteria in the cathode chamber of a two-chamber MFC achieves >90% NO₃⁻-N removal (100 mg/L initial) within four days. The GAC acts as an electron storage and transfer medium via electrical double layer formation, enabling reproducible potential generation (0.25–0.33 V) and reducing internal resistance. Enrichment of electroactive bacteria on GAC surface is critical; unenriched GAC or fresh electrodes show slower kinetics and longer lag phases (14–55 h vs. immediate response). The work is novel in applying GAC to the cathode rather than anode, but lacks systematic variation of key operating parameters like current density, HRT, and catholyte pH.

Key insights

  • Performance Enriched GAC-biocathode achieved >90% NO₃⁻-N removal in 4 days with ~40% reduction on day 1, whereas unenriched GAC achieved only ~50% over 3 days and non-GAC systems performed worse.

    So what. Pre-enrich GAC with denitrifying bacteria before deployment to maximize initial removal rate and overall efficiency; do not rely on in-situ enrichment during operation.

  • Threshold Enriched GAC showed instant potential generation with no lag phase, while new carbon cathode with enriched GAC showed 14 h lag and stainless-steel cathode showed 2 h lag; switching from enriched to new electrode caused 55 h lag even with enriched GAC present.

    So what. Electrode material and biofilm maturity dominate kinetics; stainless steel is faster than carbon cloth for lag phase recovery, but enriched biofilm is essential for reproducibility—plan for 2–55 h startup depending on electrode choice.

  • Mechanism Internal resistance decreased with GAC-biocathode enrichment compared to non-enriched systems, as shown by EIS analysis (Figure 6), indicating improved charge transfer.

    So what. Use enriched GAC to lower cathode overpotential and improve overall cell voltage; this is a mechanism for power recovery, not just denitrification.

  • Threshold CV analysis showed reduction peaks were consistent across all NO₂⁻-N concentrations tested, but NO₃⁻-N showed an unexpected oxidation hump at high concentration (100 mg/L) inconsistent with low concentrations.

    So what. NO₃⁻ reduction kinetics may be concentration-dependent or involve competing oxidation pathways at high loading; test NO₃⁻-N in the 10–50 mg/L range to avoid this anomaly.

  • Mechanism SEM revealed bacteria (slender rods, ~0.5 µm) adhered directly to GAC surface without forming thick biofilm, exploiting GAC's high porosity and mesoporous structure.

    So what. Direct electron transfer (DET) is the dominant mechanism, not mediated transfer; design cathode materials to maximize surface roughness and porosity to enhance bacterial attachment and electron access.

Contradictions3

Tensions the paper itself points to. Each side quotes the passage it comes from.

  • Within the paper Enriched GAC shows instant potential generation in one scenario but 55 h lag in another, despite both using enriched GAC.

    One side

    Enriched GAC showed instant potential generation in the MFC with no lag phase (Figure 3, Section 3.3).

    “The enriched GAC showed instant potential generation in the MFC with no lag phase.”
    Other side

    Even though enriched GAC and enriched cathode electrodes were employed, a modest increase in voltage was seen. To reach its maximum voltage output again, it took roughly 55 h (Section 3.3).

    “Even though enriched GAC and enriched cathode electrodes were employed, a modest increase in voltage was seen. To reach its maximum voltage output again, it took roughly 55 h.”

    Authors’ reading. The authors attribute the 55 h lag to media composition change (new cathode media), not GAC enrichment status. When media is replenished with the same composition, instant response is observed. This is not a true contradiction but a media-dependent effect; the paper does not fully isolate media vs. biofilm effects.

  • Within the paper Potential generation increases with stirring speed (0.25 to 0.33 V) but RPM variation shows no noticeable effect on potential or denitrification in non-enriched systems.

    One side

    The stirring speed of GAC in the cathode showed a steady growth in potential generation from 0.25 V to 0.33 V (Abstract).

    “The stirring speed of GAC in the cathode showed a steady growth in potential generation from 0.25 V to 0.33 V.”
    Other side

    When operated at different RPMs (0, 50, 100, 150 and 200), there was no noticeable effect on potential or denitrification as observed with the enriched GAC-biocathode (Section 3.3, Figure 5).

    “When operated at different RPMs (0, 50, 100, 150 and 200), there was no noticeable effect on potential or denitrification as observed with the enriched GAC-biocathode.”

    Authors’ reading. The first statement refers to enriched GAC-biocathode (Figure 4); the second refers to fresh GAC without enrichment (Figure 5). The contradiction is resolved by biofilm enrichment status: enriched systems respond to RPM, unenriched do not. The paper does not explicitly state this distinction in the abstract or early results.

  • Within the paper GAC addition to non-enriched biocathode decreases potential rather than increasing it, contrary to the anode literature cited.

    One side

    GAC has previously been integrated into the anode to form a capacitive bioanode to increase the power density (Section 4, Discussion).

    “GAC has previously been integrated into the anode to form a capacitive bioanode to increase the power density.”
    Other side

    Upon the addition of GAC particles in the media, the potential was found to decrease steadily even in the presence of NO₃⁻-N (Section 3.3, Figure 5).

    “Upon the addition of GAC particles in the media, the potential was found to decrease steadily even in the presence of NO₃⁻-N.”

    Authors’ reading. Authors explain this by stating electrons are diverted to charging GAC rather than reducing NO₃⁻-N in non-enriched systems. In enriched systems, bacteria facilitate electron transfer to both GAC and substrate. This is a mechanism-dependent effect, not a true contradiction, but the paper does not clearly state this trade-off upfront.

Opportunity areas6

Specific gaps in this paper, with an experiment that would close each.

  • High No systematic variation of initial NO₃⁻-N concentration (only 100 mg/L tested); kinetics and removal efficiency at 10, 50, 200, 500 mg/L-N are unknown.

    CV analysis (Figure 7) showed unexpected oxidation hump at 100 mg/L NO₃⁻-N but not at lower concentrations, suggesting concentration-dependent kinetics. Practical wastewater ranges 10–500 mg/L-N.

    Try. Batch denitrification with enriched GAC-biocathode at NO₃⁻-N = 10, 25, 50, 100, 200, 500 mg/L; measure removal rate (mg/L/day) and final potential (V) vs. time.

  • High No measurement of current density, charge recovery, or Faradaic efficiency; power output is reported as voltage only, not normalized to electrode area or current.

    Abstract and results report potential (V) and power generation but no current (mA), current density (mA/cm²), or Coulombic efficiency. This prevents comparison with other MES studies and assessment of electron recovery.

    Try. Measure current continuously during denitrification cycles; calculate Faradaic efficiency as (electrons transferred to NO₃⁻-N reduction) / (total electrons from anode) and current density normalized to cathode area (cm²).

  • High Hydraulic retention time (HRT) and substrate loading rate not controlled or reported; all experiments are batch mode with single 100 mg/L NO₃⁻-N dose.

    Real wastewater treatment requires continuous or semi-continuous operation. Anode is semi-continuous (10 mM acetate fed via pump) but cathode is batch. No data on how HRT or NO₃⁻-N loading rate affects removal kinetics.

    Try. Operate cathode in semi-continuous mode with peristaltic pump; vary HRT (1, 2, 4, 8 h) and NO₃⁻-N loading (50–200 mg/L/day); measure steady-state removal efficiency and N₂O/NO₂⁻ accumulation.

  • High Catholyte pH not measured or controlled; medium contains 2 g/L NaHCO₃ but final pH and pH drift during denitrification are not reported.

    Denitrification kinetics and N₂O production are pH-sensitive (typically optimal 6.5–8.0). Bicarbonate buffering capacity and pH change during 4-day batch are unknown.

    Try. Monitor catholyte pH continuously during denitrification; test pH 6.0, 7.0, 8.0, 9.0 with buffered media; measure NO₃⁻-N removal rate, N₂O accumulation, and potential vs. pH.

  • High No measurement of N₂O or NO₂⁻ accumulation; only NO₃⁻-N removal is quantified; intermediate products are not tracked.

    Denitrification intermediates (NO₂⁻, N₂O) are environmentally significant. CV shows NO₂⁻ reduction peaks (Figure 7) but no gas chromatography or ion chromatography data for N₂O or NO₂⁻ in the bulk solution during operation.

    Try. Measure NO₂⁻-N and N₂O (headspace gas chromatography) at 6, 12, 24, 48, 96 h during denitrification with enriched GAC-biocathode at 100 mg/L NO₃⁻-N; report N-balance (NO₃⁻-N → NO₂⁻-N + N₂O + N₂).

  • Medium Cathode potential (vs. Ag/AgCl or SHE) not explicitly controlled or reported; only cell voltage (Ecell) and anode potential (Ean) are shown; cathode potential (Ecat) is inferred but not set.

    Denitrification kinetics depend on cathode potential. Paper mentions 0.3 V applied during enrichment but does not report whether this is maintained during MFC operation or how it varies with current.

    Try. Use potentiostat to control cathode potential at −0.3, −0.4, −0.5, −0.6 V vs. Ag/AgCl; measure NO₃⁻-N removal rate, current, and N₂O/NO₂⁻ accumulation at each potential.

Generated by MESSAI extraction pipeline · review against source PDF

02

Extracted values

Every value pulled from the paper, with its source, so each number can be checked against the text.

n = 26 extracted values

Select a citation to see the quote, page and confidence behind a value.

0 of 26 extracted rows modelable

  • 25 not canonicalised (no canonical slug)
  • 1 no SI value
ParameterValueUnitConfidenceSourceNotesModelable
Nitrate removal93%80%
ion chromatography (fig 2)
"more than 90% denitrification was observed with the GAC-biocathode" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Cell voltage0.32V75%
labeled on fig 5 (ecell=ecat-(-ean))
"Enriched cathode in new media: Ecell = Ecat -(-Ean); 0.32V = 0.12V -(-0.2V)" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Nitrate concentration final7mg/L NO₃-N75%
ion chromatography (fig 2)
"more than 90% denitrification was observed with the GAC-biocathode ... (Fig 2 en…" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Cell voltage0.3V75%
multimeter (reproducible voltage output)
"Once the MFC started to reproduce a voltage output of 0.30 V" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Anode potential-0.2V75%
labeled on fig 5, vs ag/agcl
"Enriched cathode in new media: Ean = -0.2 V" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Cathode potential0.12V75%
labeled on fig 5, vs ag/agcl
"Enriched cathode in new media: Ecat = 0.12 V" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Anode potential-0.1V70%
labeled on fig 5, vs ag/agcl
"New cathode (plain carbon): Ean = -0.1 V" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Cell voltage0.33V70%
labeled on fig 5 (rpm 50-200)
"Increase in RPM 50,100,150 and 200: 0.33V = 0.12V -(-0.21V)" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Cell voltage0.21V70%
labeled on fig 5
"New cathode (plain carbon): 0.21V = 0.11V -(-0.1V)" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Cathode potential0.11V70%
labeled on fig 5, vs ag/agcl
"New cathode (plain carbon): Ecat = 0.11 V" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Cell voltage0.07V70%
labeled on fig 5
"the maximum voltage output was only 0.07 V ... New cathode (Stainless steel): 0.…" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Cathode potential0.04V70%
labeled on fig 5, vs ag/agcl
"New cathode (Stainless steel): Ecat = 0.04 V" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Anode potential-0.03V70%
labeled on fig 5, vs ag/agcl
"New cathode (Stainless steel): Ean = -0.03 V" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Nitrate removal day140%70%
ion chromatography (fig 2)
"maximum reduction of NO3-N on the first day (close to 40%)" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Nitrate concentration final39mg/L NO₃-N65%
ion chromatography (fig 2)
"New GAC series ~39 mg/L at day 4 (Fig 2)" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Time to max voltage14h65%
potential logging (fig 3)
"Using new media and the new cathode electrode, the MFC took approximately 14 h t…" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Nitrate removal61%60%
ion chromatography (fig 2)
"GAC without the enriched bacteria showed ... approximately 50% NO3-N reduction, …" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Cell voltage0.33V60%
potential logging (fig 4, rpm 200)
"The stirring speed of GAC in the cathode showed a steady growth in potential gen…" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Cell voltage0.25V60%
potential logging (fig 4)
"With the stainless steel, the power did not increase rapidly and took approximat…" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Nitrate concentration final66mg/L NO₃-N60%
ion chromatography (fig 2)
"Without GAC series ~66 mg/L at day 4 (Fig 2)" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Maximum cell voltage0.33V60%
potential logged every 10 min (fig 3)
"The enriched GAC showed instant potential generation in the MFC with no lag phas…" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Voltage drop 10h end0.22V60%
potential logging (fig 5)
"The voltage output decreased from 0.32 V to 0.22 V within 10 h and continued to …" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Cathode materialbiocathode—60%
extracted
Excluded: no SI value
Time to max voltage2h55%
potential logging
"The voltage output started at 0.16 V and increased to its maximum voltage output…" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Nitrate removal34%55%
ion chromatography (fig 2)
"the effect of GAC was noticeably higher irrespective of enrichment compared to t…" · T=30°C, substrate=sodium acetate (anode electron donor), fed_batchExcluded: not canonicalised (no canonical slug)
Showing 25 of 26

Methodology

What was the system and how was it run

Methodology

Methodology

Two-chamber H-type MFC (100 mL each) with cation exchange membrane separator. Anode: carbon cloth, fed 10 mM sodium acetate semi-continuously. Cathode: carbon cloth or stainless steel, initially aerobic (enrichment phase), then anoxic with 100 mg/L NO₃⁻-N. GAC (2–5 mm granules, 2 g) enriched with denitrifying bacteria in a separate bottle under potentiostatic control (0.3 V) before transfer to MFC. External resistance 1000 Ω. Potential measured every 10 min. NO₃⁻-N quantified by ion chromatography at 12–24 h intervals. Electrochemical characterization by EIS, CV, and zeta potential. Biofilm morphology by SEM.

System configuration

FieldValue
reactor typeMFC
chamber config2-chamber

Electrode specifications

FieldValue
materials["activated carbon"]

Performance metrics

FieldValue
citation count12

Operating conditions

8 runs extracted
RunT°CpHanpHcatSubstrate[S]mg/LHRThModeR_extΩV_appVInoculum
cma:air_cathode_enrichment30——sodium acetate (anode electron donor)10—fed_batch1000—anaerobic sludge, Chuncheon wastewater treatment plant, Republic of Korea (both chambers)
cma:enriched_carbon_cloth_freshGAC30——sodium acetate (anode electron donor)10—fed_batch1000—anaerobic sludge, Chuncheon wastewater treatment plant, Republic of Korea (both chambers)
cma:GAC_biocathode_enriched30——sodium acetate (anode electron donor)10—fed_batch1000—anaerobic sludge, Chuncheon wastewater treatment plant, Republic of Korea (both chambers)
cma:GAC_biocathode_SS_RPM30——sodium acetate (anode electron donor)10—fed_batch1000—anaerobic sludge, Chuncheon wastewater treatment plant, Republic of Korea (both chambers)
cma:new_GAC_no_enrichment30——sodium acetate (anode electron donor)10—fed_batch1000—anaerobic sludge, Chuncheon wastewater treatment plant, Republic of Korea (both chambers)
cma:new_plain_carbon_cathode30——sodium acetate (anode electron donor)10—fed_batch1000—anaerobic sludge, Chuncheon wastewater treatment plant, Republic of Korea (both chambers)
cma:no_GAC_cathode30——sodium acetate (anode electron donor)10—fed_batch1000—anaerobic sludge, Chuncheon wastewater treatment plant, Republic of Korea (both chambers)
cma:stainless_steel_cathode_freshGAC30——sodium acetate (anode electron donor)10—fed_batch1000—anaerobic sludge, Chuncheon wastewater treatment plant, Republic of Korea (both chambers)

Pipeline

Raw extractions, artifacts, quality signal

Extraction quality

honesty signal

Calibrate your trust in the extracted content against these signals — they're how the pipeline rated its own output for this paper.

Parameter completeness

38%

Fraction of expected parameters extracted

Data completeness

50%

Overall extraction coverage across fields

AI confidence

72%

Model self-reported confidence

Mean parameter confidence

66%

Average confidence across PaperParameter rows surfaced above

review against source PDF before citing · scores 0–1

03

Chart explorer

Move the inputs this paper used and see how the predicted outcome shifts.

04

Explore model

The reactor in 3D, with flow you can switch on and off.

05

AI insights

Contradictions, gaps and opportunities found by comparing this paper with the corpus.

06

Compare similar papers

The nearest papers by system, materials and organisms, with their outcomes side by side.

07

Source PDF

The paper as published.

loading 3D model…

Representative model, generic MFC

Representative MFC — matched on the paper’s system type only, not its reactor or geometry.

MFC
System
26
Extracted values
2023
Year

Keywords

  • Microbial fuel cell
  • Denitrifying bacteria
  • Denitrification
  • Cathode
  • Dielectric spectroscopy
  • Activated carbon

Cite

Anup Gurung, Bhim Sen Thapa, Seong-Yun Ko et al. (2023). Denitrification in Microbial Fuel Cells Using Granular Activated Carbon as an Effective Biocathode. Energies. https://doi.org/10.3390/en16020709

Journal
Energies

Open in lab for full controls, parameter editing, and template overlays.

Open in lab