Paper · MFC
Enhancing electricity generation using fungal laccase-based microbial fuel cell
- MFC
- Dual Chamber
- Membraneless
- Anode: El-ghasheem (agro-industrial…
- Membrane: Salt Bridge
- Catalyst: laccase enzyme
Summary
What the paper reports, in its own words.
Abstract
Microbial fuel cells (MFCs) are very important source to obtain green electricity and also for decontamination of waste water. Bioelectricity yield from biofuel cells is still needed for maximizing. Microbial laccases, especially those produced by fungi, are currently considered to be one of the most promising biocatalyst for bioelectricity production and also purification of water from the different pollutant, especially phenolic compounds. In the present work, different electrolyte solutions used in anode and cathode chambers to evaluate efficiency of each to produce voltage & current and also to prove that using economical electrolytes, which were agro-industrial waste called el-ghasheem at anode and only tap water at cathode, achieve good results in comparison with other commonly used electrolytes which were glucose, sodium nitrate, mono-potassium phosphate, di-potassium phosphate, ammonium chloride and magnesium sulfate. The use of El-ghasheem in the economic MFC showed power improvement results when fungal laccase, produced from Monodictys castaneae fungus, had been used as cathodic reaction catalyst to increase voltage production from 0.466±0.003 V to 0.807±0.002 V and current from 0.025±0.003 A to 0.09±0.003 A at 37 °C, anolyte pH 6 and catholyte pH 5 for 10 days incubation period. It was noticed that this laccase enzyme had the 98.38±0.264 % phenol removal activity from anode chamber through indirect effect and 99.69±0.276 % phenol removal activity from cathode chamber through direct effect when El-ghasheem was used as the organic fuel at the anode side. In this study using unstudied agro-industrial waste, Electricity was produced by the new fungal laccase which showed the high performance in electricity production enhancement and also phenol compounds removal through low cost MFC.
AI summary
72% confidenceThis paper demonstrates enhancement of electricity generation in a two-chamber microbial fuel cell (MFC) using fungal laccase (from Monodictys castaneae) as a cathode biocatalyst, combined with agro-industrial waste (el-ghasheem) as anode electrolyte. Laccase increased voltage 73% (0.466→0.807 V) and current 260% (0.025→0.09 A) at optimized conditions (37°C, anolyte pH 6, catholyte pH 5, 10 days). Phenol removal reached 98.4% at anode and 99.7% at cathode. The work prioritizes cost reduction and dual function (power + remediation) over mechanistic insight into nitrogen cycling or electrochemical kinetics.
Key insights
Threshold Catholyte pH optimum shifts from 7 (control MFC: 0.466 V) to pH 5 (laccase MFC: 0.807 V), a 1.73× voltage gain at lower pH
So what. If deploying laccase cathodes, operate at pH 5 not pH 7; this is a critical operating window shift that contradicts standard MFC practice
Threshold Laccase maintains activity for 14 days but peaks at day 10–12 (0.807 V on day 10), then declines gradually
So what. Plan batch operation cycles around day 10 harvest; do not assume continuous stable output beyond 12 days
Threshold Temperature optimum is 37°C for both control and laccase MFC; performance drops at 42°C and 20°C
So what. Maintain strict temperature control at 37°C; even 5°C deviation reduces output; this is a narrow operating window
Trade-off Anolyte pH 6 is optimal for control MFC (0.466 V, 0.025 A) but paper does not test anolyte pH with laccase cathode
So what. Anolyte pH 6 + catholyte pH 5 combination is untested; verify this pairing does not create pH gradient stress or ion transport issues
Mechanism Phenol removal is 98.4% at anode (indirect, via microbial degradation) but 99.7% at cathode (direct, via laccase), showing compartmentalization of remediation
So what. Laccase acts primarily as a direct oxidizer at cathode; anode phenol removal is microbial, not enzymatic—do not assume enzyme catalyzes both chambers
Contradictions3
Tensions the paper itself points to. Each side quotes the passage it comes from.
Within the paper Laccase activity stability claim conflicts with observed decline after day 12
One sideLaccase 'keep its activity for all of 14 days' (text, Optimization section)
“laccase keep its activity for all of 14 days, the complete incubation period”
Other sideLaccase 'achieved the maximum stimulation for bioelectricity at the range day 10-12, after that its activity decreased slightly and gradually' (text, same section)
“achieved the maximum stimulation for bioelectricity at the range day 10-12, after that its activity decreased slightly and gradually”
Authors’ reading. Authors distinguish between 'keeping activity' (remaining present) and 'peak performance' (day 10–12); activity persists but declines post-day 12, so the statements are compatible if 'activity' means presence not efficacy
Within the paper Optimal catholyte pH differs between control and laccase MFC, but paper does not explain mechanism
One sideControl MFC optimal at pH 7: '0.466±0.003 V and 0.025±0.003 A' (Figure 8, text)
“catholyte pH7 achieved the highest voltage and current, 0.466±0.003 V and 0.025±0.003 A for control MFC3 (without laccase)”
Other sideLaccase MFC optimal at pH 5: '0.807±0.002 V and 0.09±0.003 A' (Figure 8, text)
“catholyte pH 5 was the optimum pH for laccase activity and achieved the highest voltage and current, 0.807±0.002 V and 0.09±0.003 A”
Authors’ reading. Authors note that pH affects enzyme properties (activity, stability, solubility) and cite Nernst equation effects (~60 mV per pH unit), but do not quantify why laccase prefers pH 5 over pH 7 or test intermediate pH values with laccase
Within the paper MFC3 with el-ghasheem outperforms MFC2 with standard nutrients, contradicting expectation that defined media optimize performance
One sideMFC3 (el-ghasheem + tap water) achieves 0.43 V; MFC2 (standard nutrients) achieves 0.36 V (Figure 2)
“MFC3 achieved the best voltage with 0.43±0.026 V in comparison to 0.36±0.015 V using MFC2”
Other sideMFC2 uses 'commonly used electrolytes which were glucose, sodium nitrate, mono-potassium phosphate, di-potassium phosphate, ammonium chloride and magnesium sulfate' (Abstract)
“using economical electrolytes, which were agro-industrial waste called el-ghasheem at anode and only tap water at cathode, achieve good results in comparison with other commonly used electrolytes”
Authors’ reading. Authors attribute success to el-ghasheem's natural nutrient profile and microbial consortium from soil extract; they frame this as cost advantage, not mechanistic superiority, and do not analyze el-ghasheem composition
Opportunity areas6
Specific gaps in this paper, with an experiment that would close each.
High No test of anolyte pH with laccase cathode; only anolyte pH 6 used in laccase experiments
Control MFC shows anolyte pH 6 optimal (0.466 V at pH 6 vs 0.25 V at pH 4), but laccase experiments fix anolyte pH 6 and vary only catholyte pH. Interaction between anolyte and catholyte pH is not explored.
Try. Test anolyte pH 4, 5, 6, 7 with laccase cathode at fixed catholyte pH 5 and 37°C; measure voltage, current, and phenol removal to identify any synergy or antagonism
Medium No measurement of current density or power density normalized to electrode area; only absolute current and power reported
Paper states 'power and current per surface area of the anode (6 cm²) was used to calculate the power and current density' but no density values are reported in results or figures. Comparison with literature requires normalization.
Try. Recalculate and report current density (mA/cm²) and power density (mW/cm²) for all conditions; compare to laccase MFC benchmarks (e.g., Sato et al. 249.67 mV OCV cited in text)
Medium No test of external load resistance; only 1 kΩ used throughout
Paper states '1kOhm resistance was used as external load' but does not vary load to find maximum power point or internal resistance. Optimal load for laccase cathode may differ from control.
Try. Sweep external load from 100 Ω to 10 kΩ at 37°C, anolyte pH 6, catholyte pH 5 with and without laccase; plot power vs. load to identify maximum power point and internal resistance
Medium No characterization of el-ghasheem composition; phenol content assumed but not quantified beyond initial measurement
El-ghasheem is described as 'agro-industrial waste called el-ghasheem which is produced from boiling of Sugarcane juice' but no proximate analysis, C/N ratio, or full phenolic profile provided. Reproducibility and scalability limited.
Try. Analyze el-ghasheem for total organic carbon, total nitrogen, C/N ratio, phenolic compound profile (HPLC), and microbial community (16S rRNA) to enable replication and optimization
Medium No measurement of dissolved oxygen, pH gradient, or ion transport across salt bridge during operation
Paper mentions pH gradients cause ~60 mV loss per unit (Nernst equation) but does not measure actual pH drift in anode or cathode during 10-day run. Catholyte pH 5 vs anolyte pH 6 may create gradient stress.
Try. Monitor anode and cathode pH, dissolved oxygen, and conductivity daily during 10-day laccase MFC run at 37°C; correlate pH drift with voltage decline post-day 12
Low No test of laccase enzyme concentration or activity threshold; only 3 U/ml used
Paper states 'crude enzymes with 3U/ml activity' but does not vary enzyme concentration to find saturation or minimum effective dose. Cost-benefit of enzyme loading not explored.
Try. Test laccase activity from 0.5 to 10 U/ml at 37°C, anolyte pH 6, catholyte pH 5; measure voltage, current, and phenol removal to identify cost-optimal enzyme loading
Generated by MESSAI extraction pipeline · review against source PDF
Extracted values
Every value pulled from the paper, with its source, so each number can be checked against the text.
n = 64 extracted values
Select a citation to see the quote, page and confidence behind a value.
36 of 60 extracted rows modelable
- 12 not canonicalised (no canonical slug)
- 11 no SI value
- 1 contradicts other papers
| Parameter | Value | Unit | Confidence | Source | Notes | Modelable |
|---|---|---|---|---|---|---|
| Voltage | 0.466 | V | 95% | llm | conclusion | |
| Temperature | 37 | °C | 95% | llm | conclusion | |
| pH | 6 | - | 95% | llm | conclusion | |
| Substrate | glucose | — | 80% | llm | ||
| Open Circuit Voltage | 0.805 | V | 98% | extracted | "In this study using laccase at the cathode of MFC3 elevated the resulted voltage…" · T=37°C, pH(an)=7, substrate=El-ghasheem (agro-industrial waste from sugarcane juice boiling), batch | Modelable |
| Power Density (Basis Unresolved) | 0.064 | W | 98% | extracted | "A 68.75% increase in the produced current from 0.025±0.003 A to 0.08±0.002 A and…" · T=37°C, pH(an)=7, substrate=El-ghasheem (agro-industrial waste from sugarcane juice boiling), batch | Excluded: no SI value |
| Peak voltage v | 0.466 | V | 98% | extracted | T=37°C, pH(an)=6, substrate=El-ghasheem (agro-industrial waste from sugarcane juice boiling), batch | Modelable |
| Power Density (Basis Unresolved) | 0.012 | W | 98% | extracted | "The power produced was calculated using the following formula: P = I x V where P…" · T=37°C, pH(an)=6, substrate=El-ghasheem (agro-industrial waste from sugarcane juice boiling), batch | Excluded: no SI value |
| Current Density (Basis Unresolved) | 0.08 | A | 98% | extracted | "A 68.75% increase in the produced current from 0.025±0.003 A to 0.08±0.002 A and…" · T=37°C, pH(an)=7, substrate=El-ghasheem (agro-industrial waste from sugarcane juice boiling), batch | Excluded: no SI value |
| Peak voltage v | 0.805 | V | 98% | extracted | T=37°C, pH(an)=7, substrate=El-ghasheem (agro-industrial waste from sugarcane juice boiling), batch | Modelable |
| Current Density (Basis Unresolved) | 0.025 | A | 98% | extracted | "The power and current per surface area of the anode (6 cm2) was used to calculat…" · T=37°C, pH(an)=6, substrate=El-ghasheem (agro-industrial waste from sugarcane juice boiling), batch | Excluded: no SI value |
| Open Circuit Voltage | 0.466 | V | 98% | extracted | "It was noticed that this laccase enzyme had the 98.38±0.264 % phenol removal act…" · T=37°C, pH(an)=6, substrate=El-ghasheem (agro-industrial waste from sugarcane juice boiling), batch | Modelable |
| Current | 0.025 | A | 95% | digital multi-meter | "current from 0.025±0.003 A to 0.09±0.003 A" · T=37°C, pH(an)=6, substrate=el-ghasheem, steady_state | Modelable |
| Electrode Diameter | 0.5 | cm | 95% | extracted | "One end of the copper wire was attached to 4 cm long and 0.5 cm diameter graphit…" · condition_hint=design parameter for electrode, electrode_material=graphite rod | Modelable |
| Current | 0.09 | A | 95% | digital multi-meter | "catholyte pH 5 was the optimum pH for laccase activity and achieved the highest …" · T=37°C, pH(an)=5, substrate=el-ghasheem, steady_state | Modelable |
| Current | 0.09 | A | 95% | digital multi-meter | "current from 0.025±0.003 A to 0.09±0.003 A" · T=37°C, pH(an)=5, substrate=el-ghasheem, steady_state | Modelable |
| Peak Current | 0.09 | A | 95% | digital multi-meter | "current from 0.025±0.003 to 0.09±0.003 A" · T=37°C, pH(an)=5, substrate=el-ghasheem, steady_state | Modelable |
| Peak Current | 0.025 | A | 95% | digital multi-meter | "This pH achieved the highest voltage, 0.466±0.003 V, and current, 0.025±0.003 A" · T=37°C, pH(an)=6, substrate=el-ghasheem, steady_state | Modelable |
| Electrode Surface Area | 6 | cm² | 95% | extracted | "The power and current per surface area of the anode (6 cm2) was used to calculat…" · condition_hint=design parameter for anode electrode, electrode_material=graphite rod | Modelable |
| Electrode Surface Area | 4 | cm | 95% | extracted | "One end of the copper wire was attached to 4 cm long and 0.5 cm diameter graphit…" · condition_hint=design parameter for electrode, electrode_material=graphite rod | Excluded: no SI value |
| Peak Current | 0.025 | A | 95% | digital multi-meter | "catholyte pH7 achieved the highest voltage and current, 0.466±0.003 V and 0.025±…" · T=37°C, pH(an)=7, substrate=el-ghasheem, steady_state | Modelable |
| External Load | 1,000 | Ohm | 95% | extracted | "1kOhm resistance was used as external load" · condition_hint=design parameter for external circuit, external_resistance_ohm=1000 | Modelable |
| Peak Current | 0.08 | A | 95% | digital multi-meter | "A 68.75% increase in the produced current from 0.025±0.003 A to 0.08±0.002 A" · T=37°C, pH(an)=6, substrate=el-ghasheem, steady_state | Modelable |
| Phenol concentration | 25.3 | ppm | 95% | extracted | "Phenol concentrations at anode and cathode of MFC3 without laccase at day 10." · T=37°C, pH(an)=7, substrate=El-ghasheem (agro-industrial waste containing phenols), batch | Excluded: not canonicalised (no canonical slug) |
| Phenol concentration | 0.001 | ppm | 95% | extracted | "El-ghasheem phenol content in anolyte and catholyte was measured before and afte…" · T=37°C, pH(an)=6, substrate=El-ghasheem (agro-industrial waste containing phenols), batch | Excluded: not canonicalised (no canonical slug) |
Methodology
What was the system and how was it run
Methodology
Methodology
Two-chamber H-type MFC with graphite rod electrodes (4 cm × 0.5 cm), salt bridge (lamp wick in 1 M KCl), and 1 kΩ external load. Three MFC designs tested with different electrolytes; best performer (MFC3: el-ghasheem anode + tap water cathode) optimized by varying temperature (20–42°C), anolyte pH (4–7), and catholyte pH (3–8) over 10–14 days at 37°C. Laccase (3 U/ml from Monodictys castaneae) added to cathode; voltage and current measured daily with digital multimeter. Phenol quantified by FeCl₃ colorimetry at 540 nm using guaiacol standard curve.
System configuration
| Field | Value |
|---|---|
| reactor type | MFC |
| chamber config | 2-chamber |
Operational parameters
| Field | Value |
|---|---|
| p h | {"min":5,"max":6,"optimal":6} |
| temperature | {"min":37,"max":37,"optimal":37} |
| substrate | ["glucose"] |
Operating conditions
21 runs extracted| Run | T°C | pHan | pHcat | Substrate | [S]mg/L | HRTh | Mode | R_extΩ | V_appV | Inoculum |
|---|---|---|---|---|---|---|---|---|---|---|
| baseline | 37 | 6 | 5 | el-ghasheem | — | — | batch | — | — | — |
| baseline #2 | 37 | 6 | 5 | el-ghasheem | — | — | batch | — | — | — |
| control_without_laccase | 37 | 7 | 7 | el-ghasheem | — | — | batch | — | — | — |
| control_without_laccase #2 | 37 | 7 | 7 | el-ghasheem | — | — | batch | — | — | — |
| v2-05d474b1538d5315 | 37 | 7 | — | El-ghasheem (agro-industrial waste containing phenols) | — | — | batch | — | — | — |
| v2-141f6ecf42d1e9bd | 37 | 6 | — | El-ghasheem (agro-industrial waste from sugarcane juice boiling) | — | — | batch | — | — | — |
| v2-3a8eaa60654df296 | — | — | — | — | — | — | — | 1000 | — | — |
| v2-49eb3911c6b140cd | 37 | 7 | — | el-ghasheem | — | — | steady_state | 1000 | — | — |
| v2-4faa6bd8a7188e91 | 37 | 7 | — | glucose_el-ghasheem | — | — | steady_state | 1000 | — | — |
| v2-568ce878db11874b | 37 | 7 | — | acetate | — | — | steady_state | 1000 | — | — |
| v2-7e774506c7d77bd9 | 37 | 6 | — | el-ghasheem | — | — | steady_state | 1000 | — | — |
| v2-9efe7e198728080f | 37 | 7 | — | El-ghasheem (agro-industrial waste from sugarcane juice boiling) | — | — | batch | — | — | — |
| v2-aabb8442e7e3e8c7 | 37 | 8 | — | el-ghasheem | — | — | steady_state | 1000 | — | — |
| v2-bdc0834e67a8253b | 20 | 7 | — | el-ghasheem | — | — | steady_state | 1000 | — | — |
| v2-c141e56f48ac6555 | 37 | 5 | — | el-ghasheem | — | — | steady_state | 1000 | — | — |
| v2-c71809f1bba9d95b | 28 | 7 | — | el-ghasheem | — | — | steady_state | 1000 | — | — |
| v2-cdb8639ff58eb681 | 37 | 6 | — | El-ghasheem (agro-industrial waste containing phenols) | — | — | batch | — | — | — |
| v2-d99195a02ef03c53 | 37 | 4 | — | el-ghasheem | — | — | steady_state | 1000 | — | — |
| v2-e5acc20b6edab361 | — | — | — | el-ghasheem | — | — | startup | — | — | — |
| v2-f586e9af22985397 | — | — | — | — | — | — | — | — | — | — |
| v2-f8a4c73dc9ae083b | 37 | 3 | — | el-ghasheem | — | — | steady_state | 1000 | — | — |
Pipeline
Raw extractions, artifacts, quality signal
Extraction quality
honesty signalCalibrate your trust in the extracted content against these signals — they're how the pipeline rated its own output for this paper.
Parameter completeness
25%
Fraction of expected parameters extracted
Data completeness
50%
Overall extraction coverage across fields
AI confidence
72%
Model self-reported confidence
Mean parameter confidence
84%
Average confidence across PaperParameter rows surfaced above
review against source PDF before citing · scores 0–1
Chart explorer
Move the inputs this paper used and see how the predicted outcome shifts.
Explore model
The reactor in 3D, with flow you can switch on and off.
AI insights
Contradictions, gaps and opportunities found by comparing this paper with the corpus.
Compare similar papers
The nearest papers by system, materials and organisms, with their outcomes side by side.
Source PDF
The paper as published.
Representative model: Dual-chamber H-cell MFC
Tap to interactRepresentative model: Dual-chamber H-cell MFC
Representative dual-chamber H-cell — matched on the paper’s reported configuration, not its exact geometry.
In this record
Organisms, parameters and materials this paper reports. Each links to its page.
Organisms · 2
- Monodictys castaneae
- Monodictys castaneae fungus
Materials · 3
- El-ghasheem (agro-industrial waste)
- laccase enzyme
- Salt Bridge
Keywords
- Microbial fuel cell
- Laccase
- Anode
- Wastewater
- Pulp and paper industry
- Phenol
Cite
Hani Moubasher, Abdelrahman Tammam, Mahmoud Saleh (2024). Enhancing electricity generation using fungal laccase-based microbial fuel cell. Journal of microbiology, biotechnology and food sciences. https://doi.org/10.55251/jmbfs.9703
Open in lab for full controls, parameter editing, and template overlays.
Open in lab