Paper · MFC
The Effects of Surface Roughness of the Stainless-Steel Anode on Electricity Enhancement of Microbial Fuel Cell
- MFC
- Single Chamber
- Membraneless
- Bioanode Only
- Pure Culture
- Anode: Stainless Steel
Summary
What the paper reports, in its own words.
Abstract
Microorganisms actively catabolize substrate, and bioelectricity is generated. Microbial fuel cells (MFCs) could be utilized as a power generator in small devices. The discovery of species of microorganisms is called Rhodopseudomonas palustris KU-EGAT 13. The experiments have been conducted with the production of electricity from this type of microorganism in a single chamber microbial fuel cell. The study used 4 surface roughness of anode electrode single chamber micro fuel to study the performance of microbial fuel cell effect from the anode. Three stainless steel plates were polished to uniform roughness to the magnitude between 0.05 and 1 µm. After 24 h of experimentation, the rough electrode’s open-circuit voltage (OCV) and power densities were much higher than that produced by the smooth one. Moreover, the smooth surface is higher than the charge-transfer resistance of the rough electrode. The rough surface’s better electrochemical performance is due to denser biofilm grown on the surface, which was observed by scanning electron microscopy (SEM) and figuring out the microbial number in an image using an ImageJ program. HIGHLIGHTS The new discovery of species of microorganisms is called Rhodopseudomonas palustris KU-EGAT 13 which can produce electricity in a single chamber microbial fuel cell The performance of MFCs has gotten an effect from the different anode surface roughness.The biomass growth is larger than a rougher anode surface, which contributes to anode’s efficiency After observed by SEM, found that when it is in the highest anode surface roughness directed towards the number of microbes stick on the surface GRAPHICAL ABSTRACT
AI summary: matches the abstract (70% confidence) · review against source PDF
Extracted values
Every value pulled from the paper, with its source, so each number can be checked against the text.
n = 38 extracted values
Select a citation to see the quote, page and confidence behind a value.
7 of 34 extracted rows modelable
- 5 not canonicalised (no canonical slug)
- 19 no SI value
- 3 outside physical bounds
| Parameter | Value | Unit | Confidence | Source | Notes | Modelable |
|---|---|---|---|---|---|---|
| Electrode Surface Area | 20Unit not recorded in the legacy table | — | 90% | llm | methods | |
| Open Circuit Voltage | 0.421 | V | 90% | llm | results | |
| Temperature | 25 | °C | 70% | llm | methods | |
| Ambient Temperature | 25 | °C | 70% | llm | conclusion | |
| Power density | 409 | µW/m³ | 100% | extracted | "The maximum power densities of roughness 0.0858, 0.3662, 0.6601 and 0.9562 Ra we…" | Excluded: no SI value |
| Electrode Surface Roughness | 0.956 | Ra | 95% | surface roughness tester | "The final roughness of each stainless-steel anodes was approximate 0.0858, 0.366…" · T=20°C | Excluded: no SI value |
| Electrode Surface Roughness | 0.66 | Ra | 95% | surface roughness tester | "The final roughness of each stainless-steel anodes was approximate 0.0858, 0.366…" · T=20°C | Excluded: no SI value |
| Electrode Surface Roughness | 0.366 | Ra | 95% | surface roughness tester | "The final roughness of each stainless-steel anodes was approximate 0.0858, 0.366…" · T=20°C | Excluded: no SI value |
| SEM Sample Area | 25 | mm² | 95% | extracted | "Another set of 4 different surface anodes were derived from cutting 5×5 mm² of t…" · condition_hint=SEM sample preparation, 5×5 mm² cut from anode, electrode_material=stainless steel | Excluded: not canonicalised (no canonical slug) |
| Electrode Surface Roughness | 0.0858 | Ra | 95% | surface roughness tester | "The final roughness of each stainless-steel anodes was approximate 0.0858, 0.366…" · T=20°C | Excluded: no SI value |
| Power Density (Basis Unresolved)×2 | 611 | µW/m³ | 95% | extracted | "The maximum power densities of roughness 0.0858, 0.3662, 0.6601 and 0.9562 Ra we…" · batch | Excluded: no SI value |
| Power Density (Basis Unresolved) | 550 | µW/m³ | 90% | polarization_curve | "The maximum power densities of roughness 0.0858, 0.3662, 0.6601 and 0.9562 Ra we…" · batch | Excluded: no SI value |
| Power Density (Basis Unresolved) | 487 | µW/m³ | 90% | polarization_curve | "The maximum power densities of roughness 0.0858, 0.3662, 0.6601 and 0.9562 Ra we…" · batch | Excluded: no SI value |
| Power Density (Basis Unresolved) | 409 | µW/m³ | 90% | polarization_curve | "The maximum power densities of roughness 0.0858, 0.3662, 0.6601 and 0.9562 Ra we…" · batch | Excluded: no SI value |
| Power Density (Basis Unresolved) | 611 | µW/m³ | 90% | polarization_curve | "The maximum power densities of roughness 0.0858, 0.3662, 0.6601 and 0.9562 Ra we…" · batch | Excluded: no SI value |
| Bacterial Population | 18 | cells | 85% | sem imaging with imagej counting | "Figures 6 - 9 showed the results of the surface inspection by SEM and the number…" · T=20°C, steady_state | Excluded: no SI value |
| Bacterial Population | 6 | cells | 85% | sem imaging with imagej counting | "Figures 6 - 9 showed the results of the surface inspection by SEM and the number…" · T=20°C, steady_state | Excluded: no SI value |
| Bacterial Population | 117 | cells | 85% | sem imaging with imagej counting | "Figures 6 - 9 showed the results of the surface inspection by SEM and the number…" · T=20°C, steady_state | Excluded: no SI value |
| Bacterial Population | 38 | cells | 85% | sem imaging with imagej counting | "Figures 6 - 9 showed the results of the surface inspection by SEM and the number…" · T=20°C, steady_state | Excluded: no SI value |
| Membrane material | CEM | — | 80% | extracted | Excluded: no SI value | |
| Reactor type | single-chamber | — | 80% | extracted | Excluded: not canonicalised (no canonical slug) | |
| Chambers | 1 | — | 80% | extracted | Excluded: not canonicalised (no canonical slug) | |
| Power Density (Basis Unresolved) | 487 | µW/m³ | 65% | polarization curve | "The maximum power densities of roughness 0.0858, 0.3662, 0.6601 and 0.9562 Ra we…" · T=20°C, steady_state | Excluded: no SI value |
| Power Density (Basis Unresolved) | 409 | µW/m³ | 65% | polarization curve | "The maximum power densities of roughness 0.0858, 0.3662, 0.6601 and 0.9562 Ra we…" · T=20°C, steady_state | Excluded: no SI value |
| Power Density (Basis Unresolved) | 550 | µW/m³ | 65% | polarization curve | "The maximum power densities of roughness 0.0858, 0.3662, 0.6601 and 0.9562 Ra we…" · T=20°C, steady_state | Excluded: no SI value |
Methodology
What was the system and how was it run
Methodology
Methodology
The study used 4 surface roughness levels of anode electrodes in a single-chamber MFC, with experimentation lasting 24 hours.
System configuration
| Field | Value |
|---|---|
| chamber configuration | single |
| system type | MFC |
Electrode specifications
| Field | Value |
|---|---|
| materials | ["stainless steel"] |
Biological parameters
| Field | Value |
|---|---|
| microbial community | pseudomonas palustris ku-egat 13. the experiments have been conducted with the production of electricity from this type of microorganism in a single chamber microbial fuel cell. the study used 4 surface roughness of anode electrode single chamber micro fuel to study the performance of microbial fuel cell effect from the anode. three stainless steel plates were polished to uniform roughness to the magnitude between 0.05 and 1 µm. after 24 h of experimentation |
Performance metrics
| Field | Value |
|---|---|
| citation count | 4 |
Operating conditions
14 runs extracted| Run | T°C | pHan | pHcat | Substrate | [S]mg/L | HRTh | Mode | R_extΩ | V_appV | Inoculum |
|---|---|---|---|---|---|---|---|---|---|---|
| baseline_roughness_0.0858_Ra | — | — | — | — | — | — | batch | — | — | Nakhon Si Thammarat |
| baseline_roughness_0.3662_Ra | — | — | — | — | — | — | batch | — | — | Nakhon Si Thammarat |
| baseline_roughness_0.6601_Ra | — | — | — | — | — | — | batch | — | — | Nakhon Si Thammarat |
| baseline_roughness_0.9562_Ra | — | — | — | — | — | — | batch | — | — | Nakhon Si Thammarat |
| C01: Stainless steel anode (0.0858 Ra), carbon cloth cathode, 24h operation, room temperature | 20 | — | — | — | — | — | — | — | — | Rhodopseudomonas palustris KU-EGAT 13 |
| C02: Stainless steel anode (0.3662 Ra), carbon cloth cathode, 24h operation, room temperature | 20 | — | — | — | — | — | — | — | — | Rhodopseudomonas palustris KU-EGAT 13 |
| C03: Stainless steel anode (0.6601 Ra), carbon cloth cathode, 24h operation, room temperature | 20 | — | — | — | — | — | — | — | — | Rhodopseudomonas palustris KU-EGAT 13 |
| C04: Stainless steel anode (0.9562 Ra), carbon cloth cathode, 24h operation, room temperature | 20 | — | — | — | — | — | — | — | — | Rhodopseudomonas palustris KU-EGAT 13 |
| v2-0c6f878ad7b296af | 20 | — | — | — | — | — | startup | — | — | — |
| v2-9fda0fcf9f3b817f | 20 | — | — | — | — | — | steady_state | — | — | — |
| v2-d41d8cd98f00b204 | — | — | — | — | — | — | — | — | — | — |
| v2-e2e59ee6b05b2499 | 20 | — | — | — | — | — | — | — | — | — |
| v2-e400481e4d106f98 | 20 | — | — | — | — | — | — | — | — | — |
| v2-e901e361c59df443 | — | — | — | — | — | — | batch | — | — | — |
Outcomes
What was measured and what worked
Electrochemistry
8 constants| Electrode | Reaction | Parameter | Value | Unit | Conf. |
|---|---|---|---|---|---|
| anode | — | ocv_open_circuit_voltage | 0.57 | volts | 100% |
| anode | — | ocv_open_circuit_voltage | 0.6418 | volts | 100% |
| anode | — | ocv_open_circuit_voltage | 0.4933 | volts | 100% |
| anode | — | ocv_open_circuit_voltage | 0.6542 | volts | 100% |
| anode | — | ocv_open_circuit_voltage | 0.57 | volts | 100% |
| anode | — | ocv_open_circuit_voltage | 0.6418 | volts | 100% |
| anode | — | ocv_open_circuit_voltage | 0.4933 | volts | 100% |
| anode | — | ocv_open_circuit_voltage | 0.6542 | volts | 100% |
Pipeline
Raw extractions, artifacts, quality signal
Extraction quality
honesty signalCalibrate your trust in the extracted content against these signals — they're how the pipeline rated its own output for this paper.
Parameter completeness
50%
Fraction of expected parameters extracted
Data completeness
50%
Overall extraction coverage across fields
AI confidence
70%
Model self-reported confidence
Mean parameter confidence
76%
Average confidence across PaperParameter rows surfaced above
review against source PDF before citing · scores 0–1
Chart explorer
Move the inputs this paper used and see how the predicted outcome shifts.
Explore model
The reactor in 3D, with flow you can switch on and off.
AI insights
Contradictions, gaps and opportunities found by comparing this paper with the corpus.
Compare similar papers
The nearest papers by system, materials and organisms, with their outcomes side by side.
Source PDF
The paper as published.
Representative model: Single-chamber air-cathode MFC
Tap to interactRepresentative model: Single-chamber air-cathode MFC
Representative single-chamber air-cathode MFC — matched on the paper’s reported configuration, not its exact geometry.
In this record
Organisms, parameters and materials this paper reports. Each links to its page.
Materials · 3
Keywords
- Microbial fuel cell
- Anode
- Surface roughness
- Electrode
- Surface finish
- Scanning electron microscope
Cite
Thuschapol Kulchartvijit, Chamaporn Chianrabutra, Sirapan Sukontasing et al. (2022). The Effects of Surface Roughness of the Stainless-Steel Anode on Electricity Enhancement of Microbial Fuel Cell. Trends in Sciences. https://doi.org/10.48048/tis.2022.3680
- Journal
- Trends in Sciences
Open in lab for full controls, parameter editing, and template overlays.
Open in lab