Paper · MEC
Algae-assisted bioelectrochemical system with ammonium, sulfide removal and parallel biomethanation
Summary
What the paper reports, in its own words.
Abstract
In a two-section bioelectrochemical system (BES), the processes of biomethanation of ethanol stillage in the anode zone and oxygenic photosynthesis in the cathodic zone are combined.There is a reduction of ammonium ions and removal of H2S in the anode zone, and at the same time, there is a positive impact on the process of biomethanation from ethanol stillage in parallel to the anode anaerobic bioreactor.Chemical oxygen demand (COD) reductions ranging from 71.2% to 89.5% were achieved in the 3 BES operating modes studied.The dynamics of the main technological parameters in the bioanode and biocathode area of the BES during continuous operation of the anaerobic bioreactor and photobioreactor (PBR) at a contact time of 10 days is established.Depending on the selected variant of operation of BES -microbial fuel cell (MFC), microbial electrolysis cell (MEC) with 0.6V and 0.9V, a decrease in the ammonium concentration is found to varying degrees, as in the MEC mode with an external electrical voltage of 0.9V the highest degree of 76.5% is reached.At the same time, complete removal of H2S is found, in the liquid and gas phases in MEC -mode and partially (78 -84 %) in MFC -mode.The influence of the photosynthetic phases on the electrochemical parameters of MFC was also investigated, with maximum values for power and current densities of 29 W/m 2 and 115 mA/m 2 , respectively.
AI summary
72% confidenceThis paper demonstrates an algae-assisted bioelectrochemical system (BES) integrated with anaerobic digestion of ethanol stillage, achieving 76.5% ammonium removal (NH4+-N: 141–180 mg/L → 25–28 mg/L) and 89.5% COD reduction at 0.9 V MEC mode with 0.34 A/m² current density. Algae in the cathode zone generate oxygen via photosynthesis, enhancing cathodic potential and enabling complete H2S removal from biogas. The system improves methane content from 59–61% (standalone AD) to 72–75% (MEC 0.9 V) while maintaining stable biogas yield (~0.9 dm³/24h) over 80 days at 10-day HRT.
Key insights
Trade-off Ammonium removal scales with applied voltage: MEC 0.9 V achieved 76.5% removal (25 mg/L final) versus MFC 41.7% (105 mg/L final), driven by higher current density (0.34 vs 0.05 A/m²).
So what. Operators targeting >70% ammonia removal must apply ≥0.9 V external voltage; MFC mode alone is insufficient for high-nitrogen substrates.
Mechanism Dissolved oxygen in cathode zone increased from 7.5 to 8.5 mg/L during algal log-phase (days 4–12), directly raising cathodic potential and OCV from ~400 mV to 540 mV.
So what. Synchronize BES operation with algal exponential growth phase (days 4–12 in this setup) to maximize oxygen-driven cathode performance; stationary phase (day 15+) yields lower OCV.
Threshold H2S removal from biogas is complete (100%) in both MEC modes but only 78–84% in MFC mode, despite similar H2S liquid-phase removal patterns.
So what. If H2S-free biogas is critical, use MEC mode (≥0.6 V); MFC mode leaves residual H2S gas that may require downstream scrubbing.
Trade-off COD reduction correlates strongly with current density: 89.5% at 0.34 A/m² (MEC 0.9 V), 80.4% at 0.13 A/m² (MEC 0.6 V), 71.2% at 0.05 A/m² (MFC).
So what. Design for current density ≥0.3 A/m² if targeting >85% COD removal; lower densities plateau below 75%.
Performance Algal photosynthesis phase (light vs dark) modulates power density by 28% (29.0 W/m² light vs 22.6 W/m² dark) and current density marginally (115 vs 112 mA/m²), both at day 10 log-phase.
So what. Expect 20–30% power fluctuation in algae-assisted BES on a 12:12 light:dark cycle; design load resistance and external voltage to tolerate this variation.
Opportunity areas6
Specific gaps in this paper, with an experiment that would close each.
High No measurement of nitrite (NO2-) or N2O accumulation in anode or cathode zones despite ammonium removal and nitrification claims.
Paper states 'parallel process of nitrification' in cathode zone (Table 2 caption) but provides no NO2- or N2O data; ammonium removal mechanism (electrochemical vs biological nitrification) remains uncharacterized.
Try. Measure NO2-, NO3-, and N2O in both anode and cathode liquids and gas phases across all four operating modes; use isotope tracing (15N) to distinguish electrochemical oxidation from microbial nitrification.
Medium No investigation of cathode pH effect on ammonium speciation and removal efficiency.
Anode pH increased from 7.4–7.8 to 7.8–8.2 across modes (Table 2), but cathode pH not reported; ammonia/ammonium equilibrium (pKa ~9.25) and electrochemical oxidation kinetics are pH-sensitive.
Try. Vary cathode pH from 6.5 to 9.0 while holding other parameters constant; measure NH4+ removal rate and final concentration; correlate with cathodic potential and dissolved oxygen.
Medium Lack of C/N ratio optimization; only one substrate composition tested (TKN 310–325 mg/L, COD 9.45–11.90 g/L).
Paper does not vary C/N ratio or test whether ammonium removal is limited by carbon availability or electrochemical capacity; ethanol stillage C/N ratio ~30:1 is not compared to other ratios.
Try. Test C/N ratios from 10:1 to 50:1 by adjusting substrate dilution or supplementing with glucose; measure ammonium removal rate and COD consumption to identify optimal ratio.
Medium No direct measurement of electrode potential (anode and cathode) during MEC operation; only OCV and external voltage reported.
Anode and cathode potentials are shown only for open-circuit conditions (Fig. 2b); actual potentials under 0.6 V and 0.9 V applied voltage are not provided, limiting mechanistic understanding of ammonium oxidation pathway.
Try. Use potentiostat to measure anode and cathode potentials independently during MEC 0.6 V and 0.9 V operation; correlate with ammonium removal rate and current density.
Medium Biofilm composition on anode not characterized; SEM shows only morphology (coccoid bacteria 1–1.5 μm) without taxonomic or functional identification.
Paper claims 'methanogenic bacteria' on anode (Fig. 5a caption) but does not identify whether these are methanogens, exoelectrogens, or sulfate-reducers; functional role in ammonium removal unclear.
Try. Perform 16S rRNA gene sequencing and metatranscriptomics on anode biofilm; correlate microbial community composition with ammonium removal rate and current density across operating modes.
Low No investigation of ammonium migration mechanism (electrochemical vs diffusion) or cation exchange membrane (CEM) selectivity.
Paper uses CMI-7000S cation exchange membrane but does not measure ion flux, membrane potential, or selectivity; ammonium removal could be driven by electromigration, diffusion, or algal uptake.
Try. Measure ion concentrations (NH4+, Na+, K+, Ca2+) in anode, cathode, and membrane pore water; calculate Faraday efficiency for ammonium removal; test alternative membranes (AEM, bipolar) to isolate electrochemical contribution.
Generated by MESSAI extraction pipeline · review against source PDF
Extracted values
Every value pulled from the paper, with its source, so each number can be checked against the text.
n = 47 extracted values
Select a citation to see the quote, page and confidence behind a value.
15 of 47 extracted rows modelable
- 30 not canonicalised (no canonical slug)
- 1 no SI value
- 1 verifier rejected the value
| Parameter | Value | Unit | Confidence | Source | Notes | Modelable |
|---|---|---|---|---|---|---|
| Open Circuit Voltage | 540 | mV | 90% | extracted | "The highest value of the open circuit voltage (OCV= 540 mV) of the BES was measu…" · T=24°C, substrate=ethanol stillage, HRT=240h | Modelable |
| Power Density (Basis Unresolved) | 29 | W/m² | 90% | extracted | "In these measurements, the highest values of power and current density were foun…" · T=34°C, pH(an)=7.8, substrate=ethanol stillage, HRT=240h | Modelable |
| Power Density (Basis Unresolved) | 29 | W/m² | 90% | extracted | "the highest values of power and current density were found during the light phas…" · T=24°C, substrate=ethanol stillage, HRT=240h | Modelable |
| Current Density (Basis Unresolved) | 115 | mA/m² | 90% | extracted | "the highest values of power and current density were found during the light phas…" · T=24°C, substrate=ethanol stillage, HRT=240h | Modelable |
| Power Density (Basis Unresolved) | 22.6 | W/m² | 90% | extracted | "during the dark phase, respectively -22.6 W/m2 and 112 mA/m2" · T=24°C, substrate=ethanol stillage, HRT=240h | Modelable |
| Current Density (Basis Unresolved) | 112 | mA/m² | 90% | extracted | "during the dark phase, respectively -22.6 W/m2 and 112 mA/m2" · T=24°C, substrate=ethanol stillage, HRT=240h | Modelable |
| Current Density (Basis Unresolved) | 115 | mA/m² | 90% | extracted | "In these measurements, the highest values of power and current density were foun…" · T=34°C, pH(an)=7.8, substrate=ethanol stillage, HRT=240h | Modelable |
| Nitrate Concentration | 835 | mg/l | 90% | extracted | "A significant decrease in the nitrate concentration in the medium from 835 mg/l …" · T=24°C, substrate=ethanol stillage, HRT=240h | Excluded: not canonicalised (no canonical slug) |
| Nitrate Concentration | 238 | mg/l | 90% | extracted | "A significant decrease in the nitrate concentration in the medium from 835 mg/l …" · T=24°C, substrate=ethanol stillage, HRT=240h | Excluded: not canonicalised (no canonical slug) |
| Anodic Potential | 214 | mV | 90% | extracted | "Because the anodic potential throughout the period was fairly constant (203 ÷ 22…" · T=24°C, substrate=ethanol stillage, HRT=240h | Excluded: not canonicalised (no canonical slug) |
| NH₄+ Anode | 111 | mg/L | 90% | extracted | "MFC MFC 105-116" · T=34°C, pH(an)=7.8, substrate=ethanol stillage, HRT=240h | Excluded: not canonicalised (no canonical slug) |
| Chemical Oxygen Demand (COD) Anode | 3.33 | g/L | 90% | extracted | "COD (anode), g/L 2.98- 3.67" · T=34°C, pH(an)=7.8, substrate=ethanol stillage, HRT=240h | Excluded: not canonicalised (no canonical slug) |
| H₂S Liquid | 13.9 | mg/L | 90% | extracted | "H2S (in liquid), mg/L 15.4- 12. 3" · T=34°C, pH(an)=7.8, substrate=ethanol stillage, HRT=240h | Excluded: not canonicalised (no canonical slug) |
| H₂S Removal | 45.3 | % | 90% | extracted | "up to 45.3 % reduction of dissolved H2S" · T=34°C, pH(an)=7.8, substrate=ethanol stillage, HRT=240h, steady_state | Excluded: not canonicalised (no canonical slug) |
| Sulfate Removal | 70 | % | 90% | extracted | "70 % concerning sulfates" · T=34°C, pH(an)=7.8, substrate=ethanol stillage, HRT=240h, steady_state | Excluded: no SI value |
| H₂S Gas | 0.008 | % | 90% | extracted | "H2S, % 0.009- 0.007" · T=34°C, pH(an)=7.8, substrate=ethanol stillage, HRT=240h | Excluded: not canonicalised (no canonical slug) |
| CH₄ Biogas | 70 | % | 90% | extracted | "CH4, % 69-71" · T=34°C, pH(an)=7.8, substrate=ethanol stillage, HRT=240h | Excluded: not canonicalised (no canonical slug) |
| Daily Biogas Yield | 0.9 | dm³/24h | 90% | extracted | "Daily biogas yield, dm3/24h 0.88 – 0.92" · T=34°C, pH(an)=7.8, substrate=ethanol stillage, HRT=240h | Excluded: not canonicalised (no canonical slug) |
| H₂S Gas Removal | 78 | % | 90% | extracted | "a significant decrease (78-84 %) in MFC mode" · T=34°C, pH(an)=7.8, substrate=ethanol stillage, HRT=240h, steady_state | Excluded: not canonicalised (no canonical slug) |
| NH₄+ Anode | 87 | mg/L | 90% | extracted | "NH4+(anode), mg/L 84-90" · T=34°C, pH(an)=7.9, substrate=ethanol stillage, HRT=240h | Excluded: not canonicalised (no canonical slug) |
| Chemical Oxygen Demand (COD) Anode | 2.32 | g/L | 90% | extracted | "COD (anode), g/L 2.14- 2.49" · T=34°C, pH(an)=7.9, substrate=ethanol stillage, HRT=240h | Excluded: not canonicalised (no canonical slug) |
| H₂S Liquid | 4.7 | mg/L | 90% | extracted | "H2S (in liquid), mg/L 5.3- 4. 1" · T=34°C, pH(an)=7.9, substrate=ethanol stillage, HRT=240h | Excluded: not canonicalised (no canonical slug) |
| H₂S Gas×2 | 0 | % | 90% | extracted | "H2S, % 0" · T=34°C, pH(an)=7.9, substrate=ethanol stillage, HRT=240h, steady_state | Excluded: not canonicalised (no canonical slug) |
| CH₄ Biogas | 73 | % | 90% | extracted | "CH4, % 72-74" · T=34°C, pH(an)=7.9, substrate=ethanol stillage, HRT=240h | Excluded: not canonicalised (no canonical slug) |
| Daily Biogas Yield | 0.9 | dm³/24h | 90% | extracted | "Daily biogas yield, dm3/24h 0.89- 0.91" · T=34°C, pH(an)=7.9, substrate=ethanol stillage, HRT=240h | Excluded: not canonicalised (no canonical slug) |
Methodology
What was the system and how was it run
Methodology
Methodology
A two-chamber BES (anode 0.65 dm³, cathode 2.0 dm³) with graphite rod electrodes and cation exchange membrane was integrated with a 3.0 dm³ UASB anaerobic digester. Ethanol stillage (diluted 4×, COD 9.45–11.90 g/L, TKN 310–325 mg/L) was fed at 0.3 dm³/24h (10-day HRT). Four operating modes were tested: open circuit, MFC (250 Ω load), MEC (0.6 V), and MEC (0.9 V). Cathode zone contained mixed microalgae (Scenedesmus sp.) cultivated in BG11 medium under 12:12 light:dark cycle (7600–8500 Lx). Continuous online monitoring of pH, ORP, dissolved oxygen, voltage, and temperature was performed. Ammonium (Nessler method), COD (dichromate), H2S (colorimetric), sulfate (BaCl₂), and biogas composition (GC) were measured periodically over 80 days.
Operating conditions
9 runs extracted| Run | T°C | pHan | pHcat | Substrate | [S]mg/L | HRTh | Mode | R_extΩ | V_appV | Inoculum |
|---|---|---|---|---|---|---|---|---|---|---|
| v2-12439427d5206c0a | 34 | 8 | — | ethanol stillage | — | 240 | — | 10 | — | — |
| v2-2087035bea9cef4b | 34 | 7.8 | — | ethanol stillage | — | 240 | steady_state | 250 | — | — |
| v2-334c98edf41e505f | 24 | — | — | ethanol stillage | — | 240 | — | — | — | — |
| v2-3ee8dafd9aed7a69 | 34 | 7.9 | — | ethanol stillage | — | 240 | — | 10 | — | — |
| v2-5c4dc44c7495295c | 34 | 7.6 | — | ethanol stillage | — | 240 | — | — | — | — |
| v2-6b774e2fcc52a8d6 | 34 | 8 | — | ethanol stillage | — | 240 | steady_state | 10 | — | — |
| v2-7ba3b469ed04772f | 24 | — | — | ethanol stillage | — | 240 | — | 250 | — | — |
| v2-e00a217ca232dec3 | 34 | 7.8 | — | ethanol stillage | — | 240 | — | 250 | — | — |
| v2-e32a6d1d96c9e70e | 34 | 7.9 | — | ethanol stillage | — | 240 | steady_state | 10 | — | — |
Pipeline
Raw extractions, artifacts, quality signal
Extraction quality
honesty signalCalibrate your trust in the extracted content against these signals — they're how the pipeline rated its own output for this paper.
AI confidence
72%
Model self-reported confidence
Mean parameter confidence
90%
Average confidence across PaperParameter rows surfaced above
review against source PDF before citing · scores 0–1
Chart explorer
Move the inputs this paper used and see how the predicted outcome shifts.
Explore model
The reactor in 3D, with flow you can switch on and off.
AI insights
Contradictions, gaps and opportunities found by comparing this paper with the corpus.
Compare similar papers
The nearest papers by system, materials and organisms, with their outcomes side by side.
Source PDF
The paper as published.
Representative model, generic MEC
Tap to interactRepresentative model, generic MEC
Representative MEC — matched on the paper’s system type only, not its reactor or geometry.
Keywords
- Sulfide
- Chemical engineering
- Waste management
- Hydrogen sulfide
- Process engineering
- Biogas
Cite
Angelov, Bratkova, Ivanov et al. (2023). Algae-assisted bioelectrochemical system with ammonium, sulfide removal and parallel biomethanation. Bulgarian Chemical Communications. https://doi.org/10.34049/bcc.55.1.5544
Open in lab for full controls, parameter editing, and template overlays.
Open in lab